Are windshield wipers one long and one short?

1 Answers
OCali
07/24/25 8:06pm
Most vehicle models have one long and one short wiper, with the driver's side being longer and the passenger side shorter. This design ensures absolute clarity of the driver's vision, protecting the safety of passengers during rainy weather. Of course, there are also models where the driver and passenger side wipers are of equal length, primarily because these vehicles have windshields with larger curvatures. Using wipers of unequal lengths on such windshields may result in missed spots. It is recommended to replace wipers with the original size specified for the vehicle and not to increase or decrease the size arbitrarily. Methods to extend the lifespan of windshield wipers: 1. Avoid dry wiping; always spray windshield washer fluid before activating the wipers to prevent damage to the rubber blades and motor. Regularly check the level of the washer fluid. Typically, the washer fluid filler cap only indicates the "MAX" maximum level and not the minimum, so drivers should keep an eye on the fluid level and top it up when necessary. 2. If the windshield is very dirty, with sand or dust, clean off the debris before using the wipers. Do not rely solely on the wipers to clean everything, as this not only wears out the wipers but may also scratch the windshield with the dirt. 3. Using specialized wiper fluid or windshield washer fluid can better protect the wipers and improve the cleaning effect on the windshield. During winter, it is essential to choose antifreeze windshield washer fluid. 4. In cold weather, always check if the wiper blades are frozen to the windshield before use. If the wipers are stuck to the windshield due to snow or frost, never rinse them with hot water directly, as the sudden temperature change can cause the windshield to crack or the wipers to deform.
Was this review help?
17
5
Share
More Forum Discussions

How to Use the Clutch in a Manual Transmission?

Manual transmission uses the clutch in the following ways: 1. Starting: Quickly lift the clutch pedal until reaching the semi-engagement point, then slow down the lifting speed; 2. Gear shifting: Operate the clutch pedal by quickly pressing down and lifting, paying attention to coordination with the throttle; 3. Posture: Place the sole of the left foot on the clutch with the heel touching the floor, and adjust the seat so that the clutch can be fully depressed with the foot slightly bent. Precautions for using the clutch in a manual transmission include: 1. Avoid pressing the clutch for extended periods or resting the foot on the pedal to prevent premature wear of the release bearing; 2. Do not press the clutch first during emergency braking to avoid losing engine braking.
14
2
Share

How to use the cruise control on Audi A4L?

The method to use the cruise control on Audi A4L is: 1. Pull the lever inward to enter the standby cruise state, and the cruise icon will be displayed on the instrument panel; 2. When the vehicle speed reaches the specified speed or above, press the cruise control button; 3. During cruise control, pulling the lever upward can increase the vehicle speed, and pulling it downward can decrease the vehicle speed; 4. Pushing the lever outward can temporarily exit the cruise function, and pulling it inward can resume the cruise function; 5. Pushing the lever all the way outward will exit the cruise control. The Audi A4L is a medium-sized 4-door 5-seater sedan with body dimensions of: length 4858mm, width 1847mm, height 1439mm, and a wheelbase of 2908mm.
1
5
Share

What is the difference between Audi RS3 and S3?

Audi RS3 and S3 differ in the following aspects: 1. Body structure: The Audi RS3 adopts a Sportback body structure; the Audi S3 uses a sedan body structure. 2. Power: The Audi RS3 is equipped with a 2.5L inline 5-cylinder turbocharged engine; the Audi S3 is equipped with a 2.0L inline 4-cylinder turbocharged engine. 3. Body dimensions: The Audi RS3 measures 4479mm in length, 1802mm in width, and 1399mm in height; the Audi S3 measures 4474mm in length, 1796mm in width, and 1392mm in height.
1
0
Share

What Gear Should You Use When Driving a Manual Transmission Car Downhill?

Manual transmission downhill gear selection depends on specific conditions: 1. For general slopes, use 2nd gear; 2. For steep slopes exceeding 30 degrees, use 3rd gear; 3. When ascending/descending elevated roads, use 4th or 5th gear. The method for starting a manual transmission car downhill is: 1. Depress clutch and brake, shift gear lever to neutral; 2. Depress clutch and brake, turn key right to first position for vehicle self-check; 3. Turn key right to ignite; 4. After engine starts, engage 1st gear; 5. Slowly release clutch and brake, when noticeable vehicle vibration occurs, slightly release brake to start. Precautions for manual transmission downhill driving: 1. Never coast in neutral; 2. Avoid unnecessary clutch depression; 3. Do not make sudden steering wheel movements.
15
3
Share

How to Exit the Buick Radio?

To exit the Buick radio, press the button in the center of the volume control located below the center console. Taking the Buick Excelle GT 1.3T as an example, it is a compact 4-door, 5-seater sedan with body dimensions of 4609mm in length, 1798mm in width, and 1486mm in height, and a wheelbase of 2640mm. The Buick Excelle GT 1.3T is equipped with a 1.3T turbocharged engine and a 6-speed automatic transmission, delivering a maximum power of 120 kW and a maximum torque of 230 Nm. It features front-wheel drive, with a front suspension using MacPherson strut independent suspension and a rear suspension using multi-link independent suspension.
1
0
Share

What does 84h tire mean?

84h tire refers to the load index and speed rating of the tire, where 84 indicates the load index, meaning the tire can bear a weight of 500 kilograms; h indicates the speed rating, meaning the tire can handle speeds up to 210 kilometers per hour. The functions of a tire are: 1. To bear the weight of the vehicle; 2. To ensure good adhesion between the wheel and the road surface; 3. To improve the vehicle's traction, braking, and off-road capability; 4. To directly contact the road surface and work with the vehicle's suspension to cushion the impact during driving, ensuring good ride comfort and smooth driving. The maintenance methods for tires include: 1. Regularly removing debris from the tread grooves; 2. Checking the tire wear and replacing them in time; 3. Regularly checking the tire pressure; 4. Promptly repairing punctures.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.