Are there many people who fail the Subject 2 test three times?

1 Answers
DelLily
07/30/25 10:38am
There are quite a few people who fail the Subject 2 test three times, and some even fail five times. Here are some key points to note for Subject 2: 1. Control your speed well: Maintain your usual driving habits and keep your speed under control. Avoid getting nervous, as proper speed control makes everything easier. It's also important not to drive too fast, as Subject 2 requires slower speeds to allow for adjustments and ultimately pass the test. 2. Hill start and stop: This is another common area where people fail. Once you've applied the brakes, the outcome is determined, so don't overthink it. Start moving immediately, otherwise exceeding 30 seconds will result in an automatic fail. Timing is crucial here—don't make mistakes in this critical section. 3. Turn signals for parallel parking: In real-life situations, parallel parking is similar to street parking. When exiting a parking spot, you must use your turn signal for safety. During the parallel parking test, always use the left turn signal when exiting, or you'll lose points.
Was this review help?
11
4
Share
More Forum Discussions

Can a micro truck use a straw to siphon fuel from a car's gas tank?

A micro truck cannot use a straw to siphon fuel from a car's gas tank. Fuel tank design: The primary function of a car's fuel tank is to store fuel, and it is generally equipped with specific mechanisms. The fuel pump and pipelines inside the tank are strategically positioned. Typically, the fuel pump is located inside the tank, with its front end sealed and connected to the upper part of the tank. When the fuel pump is inactive, there is no direct connection between the low-pressure fuel line, return line, and the tank, ensuring that fuel does not leak even in the event of an accident. Design of the one-way valve in the fuel filler pipe: The structural design of the fuel filler pipe facilitates rapid fuel intake. Generally, the diameter of the fuel filler pipe is enlarged. In the case of a rollover accident, an excessively large diameter could lead to significant fuel leakage and potential fire hazards. Therefore, the fuel filler pipe is equipped with a one-way valve mechanism, primarily to prevent fuel leakage due to vehicular accidents.
11
1
Share

Why Are All the Dashboard Lights On?

The reasons why all the dashboard lights are on include: 1. The battery is dead or the generator is faulty. 2. Excessive dirt and carbon deposits cause unstable gas content, preventing the engine from working properly. 3. Low fuel pressure and poor constant pressure performance result in low system atomization levels. The dashboard indicators and their functions are as follows: 1. Engine warning light: Indicates an engine fault. 2. Battery indicator: Indicates the battery is depleted or the generator is faulty. 3. Oil pressure warning light: Indicates insufficient oil. 4. Coolant temperature warning light: Indicates the coolant temperature is too high. 5. Tire pressure warning light: Indicates abnormal tire pressure. 6. ABS fault warning light: Indicates an anti-lock braking system fault. 7. Antifreeze warning light: Indicates a lack of antifreeze. 8. Door ajar warning light: Indicates the door is not properly closed.
4
3
Share

What does acceleration lane mean?

Acceleration lane refers to the lane used for vehicles to accelerate before merging into the high-speed traffic flow. Below is relevant knowledge about traffic roads: Basis for road length setting: The merging area of a highway includes ramps, acceleration lanes, and the associated main road section. The traffic capacity of a highway merging area differs from that of regular road sections. Both the main road traffic volume and ramp traffic volume significantly impact the operational characteristics of the merging area. Basis for determining traffic road capacity: Highway capacity refers to the ability of a road to handle traffic flow. Through capacity analysis, traffic flow operation parameters and service level indicators can be estimated and evaluated, allowing for the proposal of improvement plans or measures to address issues on highways.
20
2
Share

Why is the car engine so loud?

Reasons for excessive engine noise: 1. Excessive carbon deposits in the engine. 2. Inappropriate engine oil usage or dirty engine oil. Introduction to engines: 1. A car engine is the device that provides power to the vehicle, serving as the heart of the car, determining its power, fuel efficiency, stability, and environmental friendliness. 2. Depending on the power source, car engines can be categorized into diesel engines, gasoline engines, electric vehicle motors, and hybrids. The working principle of a car engine is: 1. Mixing air and gasoline in a certain proportion to form a combustible mixture. 2. The intake stroke draws the mixture into the cylinder, where it is compressed, ignited, and burned to produce thermal energy. 3. The high-temperature, high-pressure gas acts on the top of the piston, driving the piston to perform reciprocating linear motion, and mechanical energy is output externally through the connecting rod, crankshaft, and flywheel mechanism.
15
2
Share

What is the difference between manual transmission and manual-automatic transmission?

Manual-automatic transmission and manual transmission differ in their shifting methods: manual-automatic transmission uses an up-push to shift up and a down-push to shift down, while manual transmission employs clutch shifting. Advantages of manual-automatic transmission cars: 1. Manual-automatic cars are easy to operate, and beginners won't stall when starting on a slope. 2. They can satisfy the driver's desire for manual shifting. 3. Combining automatic and manual transmission provides drivers with the best of both worlds. Disadvantages of manual-automatic transmission cars equipped with manual mode: 1. It can inadvertently switch to manual mode, which at high speeds can easily cause high-speed low-gear situations, damaging the transmission. 2. Higher costs. Cars equipped with automatic transmissions are significantly more expensive to purchase than pure manual cars and are less fuel-efficient compared to pure manuals. 3. Automatic transmissions are more complex than pure manual cars. They require better maintenance and are harder to repair when broken.
6
0
Share

What Items Are Checked During Vehicle Inspection?

Specific items checked during vehicle inspection: 1. Whether the vehicle comes with an instruction manual and certificate of conformity, and whether the factory inspection marks on the vehicle body are complete. 2. Measuring the internal and external dimensions of the vehicle, including wheelbase and axle track. Specific measurements include vehicle length, width, height, cargo compartment sideboard height and area, wheelbase, and axle track. 3. Conducting inspections item by item according to technical standards. Upon passing, fill out the initial vehicle inspection registration form, including the factory-specified curb weight, load capacity, passenger capacity, and driver's compartment seating capacity. 4. Checking whether the engine, chassis, body, and auxiliary equipment are clean, complete, and functional; whether the paint finish is uniform and aesthetically pleasing; whether major assemblies have been replaced; and whether these details match the initial inspection records.
5
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.