Are there height restrictions for RVs traveling on the 318 Sichuan-Tibet Line?

How to align the timing belt on a Buick Excelle engine?

Buick Excelle's timing belt is located next to the engine. The method to align the timing belt on a Buick Excelle engine is as follows: 1. Remove the right tire, accessory belt, and crankshaft pulley. 2. Remove the engine mount on the right side and the timing belt cover. 3. Rotate the crankshaft to align the timing marks. 4. Remove the timing tensioner, timing idler pulley, and timing belt. When installing the timing tensioner, ensure the internal protrusion and spring are correctly seated in their respective slots. 5. Install the timing belt. When installing the timing belt, use a hex wrench to adjust the timing tensioner to its loosest position for easier installation of the belt onto the tensioner. 6. Rotate the crankshaft two full turns and recheck the alignment of the timing marks. Finally, reinstall all removed components.

15

0

Share

Is There Any Difference Between the Grand Commander and the Commander?

There are certain differences between the Grand Commander and the Commander. The two vehicles are essentially identical in terms of exterior design, interior, configuration, powertrain, and even body dimensions. However, the key difference lies in the seating capacity—5 seats versus 7 seats. More details are as follows: 1. The Grand Commander model is split into two variants based on seating capacity: the 5-seater version is called the Commander, while the 7-seater version is named the Grand Commander. 2. Both models share the same dimensions: 4873mm in length, 1892mm in width, and 1738mm in height, with a wheelbase of 2800mm. 3. In terms of powertrain, the Grand Commander is equipped with a 2.0T turbocharged engine available in both low and high power versions. The low-power variant delivers a maximum output of 234 horsepower and 350N·m of torque, while the high-power variant produces 260 horsepower and 400N·m of torque. The high-power version also comes with an on-demand four-wheel-drive system. In this regard, the Grand Commander and the Commander share the same powertrain specifications.

14

2

Share

What is the tire size of the Volkswagen Bora?

The Volkswagen Bora is equipped with either 15-inch or 16-inch tires depending on the model, with specifications of 205/55r16 and 195/65r15. The tire model number is located on the side of the tire, and the tire size is usually represented by a set of numbers. The first number indicates the tire section width, and the latter indicates the rim diameter in inches. Here is some information about car tires: 1. Car tires are one of the important components of a vehicle. They directly contact the road surface and, together with the car suspension, help to cushion the impact during driving, ensuring good ride comfort and smoothness. They also ensure good adhesion between the wheels and the road, improve the car's traction, braking, and off-road capability, and bear the weight of the car. 2. Passenger cars generally use radial tires. The specifications of radial tires include width, aspect ratio, inner diameter, and speed limit symbols.

4

Share

How to Cancel BMW Auto Start-Stop?

To turn off the BMW auto start-stop function: Locate the auto start-stop deactivation button below the engine start button and manually press the Aoff button to disable the auto start-stop feature. Below is relevant information: 1. The auto start-stop function automatically shuts off the engine when the vehicle comes to a temporary stop during driving; when it's time to move forward again, the system automatically restarts the engine, thereby reducing unnecessary fuel consumption. Auto start-stop is primarily designed for urban road use, such as when the car is waiting at traffic lights, and is not needed during highway driving. 2. Avoid using the start-stop function when the vehicle is on a slope. If the engine does not start after releasing the brake on a slope, it may cause the vehicle to roll backward, so it should be turned off. Additionally, be sure to turn off the auto start-stop function when driving through waterlogged roads. If driving daily in the city, you can keep the auto start-stop function on.

16

3

Share

How many points are deducted for reversing in a tunnel?

Reversing in a tunnel results in a deduction of 12 points. According to traffic management laws and regulations, if a driver fails to overtake, yield, or drives in the opposite direction as required by traffic rules, their license will be deducted 3 points at once. If a driver reverses a motor vehicle in a tunnel, their license will be deducted 12 points at once. Below are the relevant rules for driving in tunnels: Do not change lanes or stop arbitrarily. When driving in a tunnel, you must not change lanes or stop arbitrarily. If your vehicle breaks down in the tunnel, turn on the hazard warning lights promptly. Maintain a safe distance. When driving in a tunnel, you should keep a sufficient safe driving distance and turn on your headlights before entering the tunnel. Although most tunnels are equipped with lighting, the brightness is often very dim, so turning on your headlights increases visibility. Also, turn on your taillights to alert drivers behind you. Pay attention to speed. When driving in a tunnel, vehicles must adhere to the posted speed limit. Drivers must maintain their speed according to the limit indicated on the speed signs outside the tunnel entrance and avoid speeding. Additionally, overtaking is strictly prohibited within the tunnel lanes. When approaching an uncontrolled single-lane tunnel, carefully observe both the tunnel entrance and the opposite end. If there are already vehicles inside the tunnel, yield the right of way. If vehicles from the opposite end are about to enter, use your lights to signal. Once the incoming vehicle enters the tunnel, you should stop immediately. If the other party yields, proceed quickly but avoid rushing. Slow down in advance. Reduce speed when entering the tunnel. About 50 meters before the tunnel entrance, turn on your headlights, width lights, and taillights, and check your speedometer to adjust your speed according to the posted limit.

9

3

Share

What are the rules for starting on a slope?

Subject 2 exam project: The specific rules for starting on a slope are as follows: 1. If the car body presses the right line, it is disqualified. 2. If the front of the car is not within the three lines, it is disqualified. 3. If the distance between the car body and the side line is greater or less than 20 centimeters, 10 points are deducted. 4. If the car rolls back more than 30 centimeters, it is disqualified. Below is a detailed introduction to the Subject 2 exam: 1. Exam projects: Reverse parking, parallel parking, stopping on a slope, right-angle turns, and curve driving. 2. Starting on a slope is part of stopping on a slope. It requires the examinee to start the car parked on a steep slope upwards, increase the throttle to 2000 RPM, release the clutch to 1000 RPM, and then start with half-clutch and throttle. During the exam, the examinee needs to shift to first gear, release the handbrake, release the clutch, and ensure the car steadily climbs the slope.

6

1

Share

Are there height restrictions for RVs traveling on the 318 Sichuan-Tibet Line?

How to align the timing belt on a Buick Excelle engine?

Is There Any Difference Between the Grand Commander and the Commander?

What is the tire size of the Volkswagen Bora?

How to Cancel BMW Auto Start-Stop?

How many points are deducted for reversing in a tunnel?

What are the rules for starting on a slope?

What to Do When the ABS Light in the Car Is On?

What are the differences between the Avancier 240 and 370?

What's the reason why the Tayron won't start?

What are the differences between BYD Qin Online Ride-hailing Version and Elite Version?