Are there any clothing requirements for the Subject 2 driving test?

Why won't my old Magotan start?

Old Magotan won't start due to electrical circuit failure. Specific reasons: Clogged fuel filter, blocked fuel pump screen, severe carbon buildup or erosion of spark plugs, non-functioning starter motor, delayed fuel supply from oil pump during cold starts, insufficient fresh air or inadequate fuel supply. Solutions: Press the accelerator when starting to increase throttle opening, allowing more air intake and fuel injection for easier ignition. There are many other reasons that may prevent a car from starting, including broken circuits, dead battery, water in engine, etc. However, these situations will trigger warning lights, and the car must be inspected at a repair shop. The two most common situations are dead battery (note that battery lifespan is generally about 2 years or 80,000 km) and battery drain (most vehicles will give warnings for this). It's important to note that idling consumes electricity without charging the battery.

2

3

Share

Why is the BMW G38 engine malfunction indicator light on?

The main reasons for the engine malfunction indicator light to come on include sensor issues, car maintenance problems, fuel and oil quality issues, poor combustion of the air-fuel mixture, engine intake problems, turbocharging issues, exhaust system problems, and anti-theft system malfunctions. Additionally, when starting the car, the vehicle performs a self-check on the engine system. Normally, the engine malfunction indicator light will turn off after the self-check is completed. If it remains on for an extended period, it is advisable to seek professional assistance at a service station to diagnose and eliminate potential safety hazards. Detailed explanations for each type of fault are as follows: Sensor Issues: Sensors include coolant temperature, crankshaft position, air flow, intake temperature, and oxygen sensors. When these sensors are damaged, have poor contact, or signal interruptions occur, the car's ECU cannot accurately obtain engine data, leading to the engine malfunction indicator light turning on. In such cases, promptly visit a service center for professional inspection to eliminate safety hazards. Maintenance Issues: Poor engine maintenance is the most common cause of the engine malfunction indicator light coming on. Vehicles have specific maintenance cycles. If maintenance is not performed on schedule, combined with poor driving habits, the engine's operational burden increases, ultimately causing the engine malfunction indicator light to illuminate as a warning. Fuel and Oil Quality Issues: This refers to the quality of both fuel and engine oil. The fuel used in cars typically has a specific octane rating, and engine oil can be semi-synthetic or fully synthetic. Manufacturers usually recommend the type of fuel and engine oil to use. If the owner fails to follow these recommendations over time, it can lead to engine wear and trigger the malfunction indicator light. Always use the recommended fuel octane rating and appropriate engine oil. Poor Combustion of the Air-Fuel Mixture: Faulty spark plugs, ignition coils, fuel pumps, or clogged fuel lines can cause poor combustion of the air-fuel mixture. This leads to engine carbon buildup or knocking, which is detected by the engine's oxygen sensors and reported to the ECU, resulting in the malfunction indicator light turning on as a warning. Intake Issues: Engine combustion requires air intake, making the air filter crucial. If the car's air filter is dirty or not cleaned regularly, it can affect the intake, potentially leading to blockages over time. In severe cases, this can cause the engine malfunction indicator light to illuminate. Turbocharging Issues: Problems with the intake turbocharging system or turbocharger can also trigger the engine malfunction indicator light. The most common issue is a damaged turbocharger, accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Exhaust Issues: Faults in the rear oxygen sensor, catalytic converter, exhaust camshaft, or bearings can cause the engine malfunction indicator light to come on. The most common issue is a faulty catalytic converter, often caused by using leaded gasoline, lead or silicon-based oil additives, physical damage to the catalytic converter, or fuel system malfunctions. Anti-Theft System: If the car's electronic anti-theft system malfunctions or the anti-theft controller does not match the engine's electronic controller, the anti-theft system can prevent the engine from operating normally, also triggering the malfunction indicator light. Solutions for the Engine Malfunction Indicator Light: If the engine malfunction indicator light is on and the car cannot start, this may be due to a faulty fuel pump or ignition components. In such cases, it is recommended to call for assistance immediately. If the engine malfunction indicator light is on and the car can still be driven but exhibits severe shaking or loss of power, pull over safely and call for roadside assistance. If the engine malfunction indicator light is on but no abnormal driving symptoms are present, this may indicate a faulty sensor. In such cases, you can continue driving cautiously at low to moderate speeds but should visit a repair shop as soon as possible to address the issue.

12

3

Share

How to Check Tire Pressure Display on Hongqi H5?

On the right side of the steering wheel, there is a dial. By turning the dial, you can access and view the car's tire pressure. There are three commonly used tire pressure monitoring methods: Direct Tire Pressure Monitoring: Direct tire pressure monitoring devices use pressure sensors installed in each tire to directly measure the tire's air pressure. Wireless transmitters send the pressure information from inside the tire to a central receiver module, which then displays the tire pressure data for each tire. When the tire pressure is too low or there is a leak, the system will automatically issue an alert. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that wheel to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors the tire pressure. Indirect tire pressure alert systems essentially rely on calculating the rolling radius of the tires to monitor pressure. Introduction to Tire Pressure Monitoring System (TPMS): This system combines the advantages of both the above methods. It equips direct sensors in two diagonally opposite tires and includes a 4-wheel indirect system. Compared to a full direct system, this hybrid system can reduce costs and overcome the indirect system's inability to detect when multiple tires simultaneously have low pressure. However, it still cannot provide real-time data of the actual pressure in all four tires, as a direct system does.

17

3

Share

What is the normal water temperature for a BMW?

BMW cars have a normal water temperature of 90°C. Here is a detailed introduction about the car cooling system: 1. Temperature: The engine coolant temperature should not be too low or too high, but must be within a certain range. The normal temperature is the center position of the gauge, which is 90°C. After the vehicle starts, the antifreeze temperature rises rapidly. Once the pointer reaches the center position, the heat exchange balance ensures the antifreeze temperature no longer rises. Generally, it is optimal to start driving when the temperature reaches the middle position, which is one of the reasons why it is necessary to warm up the car before driving. 2. Cooling system faults: Generally, cooling system faults mainly include liquid leakage, insufficient coolant, radiator fan failure, and circulation water pump failure. When a car engine operates normally, it requires a certain working temperature. Neither too high nor too low is conducive to the normal operation and performance of the engine. On the other hand, the heat generated by the engine is difficult to meet the demand with conventional air cooling, so water cooling is widely adopted in car engine designs. 3. Function of the cooling system: To maintain the engine working within the most favorable temperature range, thereby improving engine power, reducing engine wear, and fuel consumption. Both excessively high and low temperatures will adversely affect the engine's operation.

8

0

Share

What Causes the Dry Grinding Sound When Folding the Rearview Mirror?

Rearview mirror folding noise is generally caused by insufficient lubrication of the internal torsion spring in the rearview mirror. You can disassemble the rearview mirror cover, spray lubricant on both ends of the spring, then manually fold and unfold the rearview mirror to see if the noise disappears. Repeat the process of spraying, folding, and unfolding multiple times until the noise is eliminated. Patterns of noise occurrence: One is during hot summer days when the sealing components expand due to heat and lack of lubrication; another is after rain or car washing, as the vehicle gets dirty, and tiny debris washed by rain or car washing adheres to the rearview mirror base and sealing components. Solutions: Manually extend and retract the rearview mirror, cleaning all visible rotating components connected to the rearview mirror during extension and retraction. After wiping clean, apply WD-40 rust-preventive lubricant to the rotating parts, spraying during both folding and unfolding. Plastic and wiring components may have gaps, misalignment, or movement, especially after exposure to sunlight, which can easily lead to such situations, causing the vehicle to produce abnormal noises on bumpy roads due to squeezing and loosening. The sound of electric current in the car mostly occurs when the vehicle is just started, especially during cold starts, when audio, air conditioning, wipers, and other devices are immediately or automatically turned on. The noise will automatically disappear after the engine warms up or the vehicle runs stably.

16

5

Share

How to Use the Auto Hold Function in Arrizo 5

Step on the vehicle's brake pedal and fasten the seat belt, then start the engine. Press the AUTO-HOLD button on the center console to activate the auto hold function. When parking and locking the vehicle, there's no need to pull the handbrake - the system will automatically brake the wheels.

12

1

Share

Are there any clothing requirements for the Subject 2 driving test?

Why won't my old Magotan start?

Why is the BMW G38 engine malfunction indicator light on?

How to Check Tire Pressure Display on Hongqi H5?

What is the normal water temperature for a BMW?

What Causes the Dry Grinding Sound When Folding the Rearview Mirror?

How to Use the Auto Hold Function in Arrizo 5

When is the timing for reversing half a turn and a full turn in the parking maneuver?

What does DSG mean in sedans?

How long should you wait to turn off the engine after driving a turbocharged car at high speed?

What transmission is used in the Zotye T700?