Are the Vehicle Identification Number and Chassis Number the Same Thing?

1 Answers
SanArabella
07/29/25 4:34pm
Chassis number is exactly the same as the vehicle identification code. The vehicle identification code is also called VIN code, chassis number, commonly known as frame number, seventeen-digit code, etc. It consists of seventeen characters. The VIN code is the ID card of a car, just like a person's ID card, the VIN code of each car is different. Here is more information about the vehicle identification number: 1. The chassis number, which is the vehicle identification code, is a code composed of 17 digits and letters. After permutation and combination, it can ensure that the same car model will not have duplicates within 30 years. 2. The last 6 digits of the chassis number are very significant. Based on these digits, all information about the car can be queried. When you need to handle some business for your car, you only need to report the last six digits to clearly know the model you purchased and the relevant information of the car.
Was this review help?
6
5
Share
More Forum Discussions

What was the earliest diesel engine?

The earliest diesel engine was successfully manufactured by Diesel as the world's first experimental diesel engine (bore 15 cm, stroke 40 cm). In 1890, Diesel returned to Berlin and devoted himself to the study of power engines. Diesel hoped to create a diesel engine that was better than gasoline engines. By 1897, theoretically, diesel engines had higher efficiency than gasoline engines and were more suitable as power sources for ships; additionally, diesel engines did not require electronic ignition, and the diesel fuel they used was cheaper than gasoline. The first engine had a power output of 13 kW, with small heat loss and an efficiency of 38%, far surpassing that of steam engines and gasoline engines. Soon, this type of machine became widely used as a stationary engine in power plants. After continuous improvements, it is now not only used in ships but also widely applied in large buses and trucks.
19
0
Share

Does Installing a Secondary Brake Affect a New Car?

Installing a secondary brake in a new car has negative effects, as it can deprive the driver of autonomy and compromise safety. Loss of Autonomy: Novice drivers lack anticipatory judgment. Upon hearing an emergency command, they might panic and mistake the accelerator for the brake. Even with the assistance of a secondary brake, prolonged use can lead to dependency. While this may resolve immediate crises, it fails to foster independent decision-making. The novice driver remains like a puppet, struggling to grow quickly. Safety Risks: A basic secondary brake functions similarly to a bicycle handbrake. If pressed too hard or too frequently, it may fail to return fully or at all. Driving under such conditions is akin to pressing both the brake and accelerator simultaneously—dragging the brakes while driving. Within a short time, a burning smell may emerge, and the brake pads could quickly wear out.
4
4
Share

What Belts Does the Engine Have?

The engine contains several belts including the timing belt, balance shaft belt, alternator and water pump belt, air conditioning belt, and power steering pump belt. A broken timing belt can cause damage to the car and requires regular replacement. Impact of the Timing Belt: If the timing belt is damaged, it can lead to loss of power and abnormal engine noises. In severe cases, it may cause the engine to fail completely. When the timing belt breaks, the engine's pistons continue to move up and down due to inertia, while the valves and ignition system stop functioning properly. This can cause the pistons to collide with the valves, resulting in deformation of both components and engine failure. Minor collisions may lead to power loss or engine issues, while severe collisions can render the car inoperable. Replacement Interval: The timing belt works in conjunction with the crankshaft to maintain the correct transmission ratio for proper engine operation. As a wear-prone component, the timing belt is susceptible to aging and should be replaced approximately every 50,000 kilometers.
13
3
Share

What lubricant is used for tire installation?

Tire grease is used. Grease can be divided into four categories. Bearing grease: A lubricating oil formulated with low-viscosity synthetic lubricating oil and various additives such as antioxidants and anti-corrosion agents. High-temperature grease: Contains a high concentration of PTFE (polytetrafluoroethylene) lubricating particles, with strong high-temperature resistance and pressure-bearing capacity, suitable for high-temperature and heavy-duty equipment. Lithium-based grease: Made from natural fatty acid lithium soap, thickened with medium-viscosity mineral lubricating oil or synthetic lubricating oil, or from synthetic fatty acid lithium soap, thickened with medium-viscosity mineral lubricating oil. Silicone grease: Abbreviated as silicone grease, it is made by thickening lubricating oil with silicone as the thickener.
3
4
Share

How to reset the maintenance light on Dongfeng Fengshen AX3?

Dongfeng Fengshen AX3 manual maintenance light reset operation method is as follows: 1. Turn on the ignition switch, press the reset button on the instrument panel with your left hand, and turn off the ignition switch with your right hand. 2. Keep pressing the reset button with your left hand without releasing it until the clock display on the instrument panel and the mileage display turn to a black screen, then release the button. 3. Press the reset button with your left hand again, then turn on the ignition switch again. At this time, the maintenance reminder on the instrument panel will start flashing. 4. Remember to keep pressing the reset button without releasing it, and wait until the maintenance reminder light stops flashing. 5. Still keep pressing the reset button without releasing it, wait until the maintenance reminder light stops flashing, then release the button. The maintenance reminder light reset is now complete. 6. Turn on the ignition switch or start the vehicle again to check if the reset was successful.
16
1
Share

How to Check if a Vehicle Has Passed the Annual Inspection?

Here are the methods to check if a vehicle has passed the annual inspection: 1. Vehicle License. Look at the vehicle license, the registration date at the bottom of the original copy indicates the month of the vehicle's annual inspection. 2. Annual Inspection Sticker. On the white side of the annual inspection sticker, the inspection validity period is printed, which is the final deadline month for the annual inspection, and it can also be done three months in advance. 3. Compulsory Insurance Policy. The compulsory insurance policy contains the vehicle's registration date. 4. Log in to the Traffic Management 12123 platform or the Cheqianqiu Vehicle Inspection Service Platform and bind the vehicle information. The vehicle's inspection date and whether it needs an annual inspection can be checked. 5. Bring the vehicle license to the vehicle management office or vehicle inspection station and ask the staff to help check if the vehicle has passed the annual inspection.
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.