Are the Test Questions for Automatic and Manual Transmission the Same in Subject One?

Is the Haima M6 fuel filter internal or external?

The Haima M6 fuel filter is installed in front of the fuel tank at the bottom of the vehicle body, which is an external type. Both ends of the fuel filter are secured with disposable clips, with a general replacement interval of 10,000 km and a mandatory replacement interval of 30,000 km. Below are the relevant details: 1. Fuel filters are categorized into carburetor type and electronic injection type. For gasoline engines using a carburetor, the fuel filter is located on the inlet side of the fuel pump, operating under lower pressure, and usually features a nylon housing. In electronic injection engines, the fuel filter is positioned on the outlet side of the fuel pump, operating under higher pressure, and typically has a metal housing. 2. The primary function of the fuel filter is to remove impurities from the gasoline. 3. If the fuel filter is excessively dirty or clogged, the main symptoms include: slower power response when accelerating; difficulty starting the car, sometimes requiring 2-5 ignition attempts to start.

11

2

Share

Does Cruise Control Save Fuel?

Cruise control saves fuel. By maintaining a fixed speed, cruise control optimizes throttle operation and precisely controls fuel injection. Theoretically, this is indeed much more fuel-efficient than some novice drivers constantly switching between the accelerator and brake to control speed. The primary function of cruise control is to automatically maintain a constant speed, relieving the driver from manually adjusting the throttle. This feature is designed to reduce driver fatigue during highway driving, rather than being specifically intended for fuel savings. Also known as speed control or autonomous driving system, cruise control allows drivers to avoid manually controlling the vehicle's speed during long highway trips, reducing fatigue and unnecessary speed fluctuations, which in turn helps save fuel.

7

3

Share

How to Set Up Auto-Lock for the Ford Kuga?

To enable the auto-lock feature on the Ford Kuga, it is necessary to modify the vehicle's onboard computer data through reprogramming. However, the auto-lock function on the Ford Kuga allows doors to be opened from inside at any time, and there is also a manual lock feature on the driver's side door panel. Below are relevant details: 1. The auto-lock function is designed for anti-theft purposes. It automatically locks the doors shortly after the vehicle starts moving, helping prevent carjacking during traffic jams or at red lights, thereby enhancing security. 2. It also provides protection when child passengers are in the car, preventing them from opening the door handles during travel and falling out, which could lead to personal injury. 3. Drivers should not overly rely on the auto-lock feature. Instead, they should proactively enhance safety awareness by manually locking doors immediately after all passengers enter the vehicle. Cultivating good driving habits ensures the safety of all occupants during travel.

2

1

Share

What Causes the Car Battery Warning Light to Illuminate?

Reasons for the car battery warning light to illuminate: 1. The alternator has malfunctioned and cannot charge the battery properly; 2. The alternator belt is broken, loose, or slipping, preventing it from charging the battery; 3. The battery's positive and negative terminals are loose or severely oxidized, causing poor contact; 4. The battery is excessively worn or discharged, leading to an inability to store power properly. If the battery has been in use for too long, it should be replaced promptly. If the driver notices the battery warning light illuminated while driving, it is advisable to pull over immediately. The illumination of the battery light indicates a fault in the vehicle's charging system. Continuing to drive under such conditions may lead to the battery draining completely, causing the car to stall and potentially creating safety hazards.

6

4

Share

How Long Should You Keep the Engine Running After a Jump Start?

Generally, when a car needs to be jump-started due to a dead battery, the engine should be kept running for about half an hour before turning it off. The exact duration may vary depending on the remaining charge of the battery. Here's the detailed procedure for jump-starting a car: 1. Take one jumper cable and connect one end to the positive terminal of the donor car's battery, then connect the other end to the positive terminal of the dead battery. 2. Take another jumper cable and connect one end to the negative terminal of the donor car's battery, then connect the other end to an unpainted metal surface on the engine block of the car with the dead battery. 3. Start the donor car, then start the disabled car following normal starting procedures. 4. After successfully starting the disabled car, let it idle for about half an hour to recharge the battery. Always connect the positive terminals first and then the negative terminals when jump-starting; when disconnecting, remove the negative cables first followed by the positive ones. Important notes about car batteries: 1. Disconnect the battery if the car won't be used for an extended period to prevent power drain and battery discharge. 2. Regularly check and maintain the battery's charge level. 3. Avoid using electronic devices in the car when the engine is off. 4. Do not perform any battery operations in high-temperature conditions. 5. When replacing the battery, it's best to use an original equipment manufacturer (OEM) battery.

1

Share

What does the faucet light displayed on the car mean?

The faucet light displayed on the car is the engine status indicator light. This indicator light is used to display the working condition of the vehicle's engine. When starting the vehicle, the light will illuminate during the self-check and then automatically turn off. If the light remains on, it indicates issues such as poor engine combustion, engine knocking, poor fuel quality, or internal engine cylinder contamination. The engine fault light is controlled by the engine computer, which essentially manages all electrical components of the engine. Therefore, any faults will be displayed through the engine fault light. There are many reasons why the engine fault light may illuminate, including issues with the purge solenoid valve controlling fuel vapor emissions, air flow meter failure, ignition coil failure, thermostat failure, catalytic converter failure, oxygen sensor failure, excessive carbon buildup in the electronic throttle, etc.

4

3

Share

Are the Test Questions for Automatic and Manual Transmission the Same in Subject One?

Is the Haima M6 fuel filter internal or external?

Does Cruise Control Save Fuel?

How to Set Up Auto-Lock for the Ford Kuga?

What Causes the Car Battery Warning Light to Illuminate?

How Long Should You Keep the Engine Running After a Jump Start?

What does the faucet light displayed on the car mean?

When will FAW-Volkswagen's mid-size SUV be launched?

What is the standard operating procedure for car maintenance?

Has the New Santana Been Discontinued?

Does the Subaru BRZ comply with China 6 emission standards?