Are the GLC260 and GLC300 the same size?

1 Answers
FernandoLee
07/30/25 4:45am
glc260 and glc300 are not the same size. The differences between the Mercedes-Benz GLC260 and GLC300 are: different engines, different maximum torque, and different maximum horsepower. Here are the specific details: 1. Different engines: The Mercedes-Benz GLC260 is equipped with a 145kW (2.0L turbocharged) engine. The Mercedes-Benz GLC300 is equipped with a 180kW (2.0L turbocharged) engine. 2. Different maximum torque: The GLC260 has a maximum torque (Nm/rpm) of 320/1650-4000. The GLC300 has a maximum torque (Nm/rpm) of 370/1300-4000. 3. Different maximum horsepower: The GLC260 has a maximum horsepower (Ps) of 197. The GLC300 has a maximum horsepower (Ps) of 245.
Was this review help?
5
2
Share
More Forum Discussions

What are the precursors of EA888 timing chain failure?

Here are the precursors of EA888 timing chain failure: 1. During driving, the engine will produce obvious abnormal noises. After tooth skipping occurs, the ignition timing will change, fuel consumption will increase, and power output will significantly decrease. If not replaced in time, it may even directly lead to engine failure. 2. After driving for a certain mileage, the car will experience varying degrees of increased fuel consumption. This is not solely caused by timing chain failure, so a comprehensive inspection is recommended. 3. If it's a normal phenomenon, maintenance is suggested. The decrease in power output is largely caused by the engine and related component configurations. Once the timing chain fails, it will restrict cylinder movement and affect the intake and exhaust functions.
8
4
Share

What are the causes of compressor damage?

Automobile compressor damage can be attributed to the following reasons: 1. When the air conditioning is turned on, the clutch pressure plate and pulley are not synchronized, especially during vehicle acceleration, where the lack of synchronization becomes more apparent. 2. The clutch emits a sharp screeching sound. 3. Sometimes sparks or smoke may be visible at the contact surface between the pressure plate and pulley. 4. Poor or complete lack of cooling in the air conditioning system. Precautions for repairing automobile compressors include: 1. Excessive clutch gap. After turning off the air conditioning, use a feeler gauge to measure the clutch gap, which is significantly larger than the standard value. This is mainly caused by clutch wear or improper adjustment during clutch maintenance. 2. Oil contamination on the clutch surface. The clutch slips due to insufficient static friction, caused by oil leakage from the front oil seal of the engine or accidental oil spillage on the clutch during maintenance. 3. Excessive clutch wear. Prolonged operation of the air conditioning can easily lead to clutch wear and warping deformation, resulting in slipping.
7
2
Share

What are the reasons for Passat idling shake?

Passat idling shake may be caused by the following reasons: 1. The most common cause of car shaking is a dirty throttle or excessive carbon deposits in the fuel injector. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold start injector will be largely absorbed by the carbon deposits, resulting in an excessively lean air-fuel mixture during cold starts, making it difficult to start. 2. Aging engine components: Car shaking is also related to the aging of engine mounts (also known as engine mounts). Engine mounts are essentially the shock absorption system of the engine, responsible for absorbing minor vibrations during engine operation. If the engine mounts are faulty, these vibrations will be transmitted to the steering wheel and the interior of the car, causing shaking during idling.
16
1
Share

What gear should an automatic transmission car be in when waiting at a red light?

When waiting at a red light with an automatic transmission car, it should be shifted into neutral. The gear positions for automatic transmission vehicles are explained as follows: 1.P——Parking, the parking gear. When the car is parked and not in use, the gear is in this position, at which time the wheels are mechanically locked to prevent rolling. 2.R——Reverse gear, used when reversing. 3.N——Neutral, used when temporarily stopping (e.g., at a red light). 4.D——Drive, also known as the forward gear, used when moving forward. 5.L——Low, the low gear, used when going downhill. 6.OD, the overdrive gear, used when driving at high speeds.
16
2
Share

Unveiling the Truth: Can Fuel Savers Really Save Fuel?

Automotive fuel savers can indeed save fuel. Below is the working principle of fuel savers: 1. An onboard automotive fuel saver is a compact gas generation device that employs Faraday's electrolysis principle, using water electrolysis to produce hydrogen and oxygen. This provides the vehicle's combustion system with hydrogen as a new energy source while also supplying oxygen to ensure complete combustion of hydrocarbon fuels. The hydrogen and oxygen mixture is introduced into the engine's intake port, entering the cylinder combustion chamber where it mixes with fuel and air to create explosive combustion. 2. Hydrogen possesses 2.8 times the energy content of gasoline by mass, requires only one-tenth the ignition energy of gasoline, has a lower ignition point making it easier to ignite, burns five times faster than gasoline, and has an extinction gap of 0.06 seconds - merely one-third of gasoline's 0.18 seconds. This smaller extinction gap allows flames to propagate to every corner of the cylinder, even reaching piston ring clearances. Therefore, adding hydrogen to the air-fuel mixture significantly improves combustion efficiency.
13
1
Share

What happens if you add too much engine oil?

The effects of adding too much engine oil are as follows: 1. Various components of the engine will vibrate during operation. 2. Excessive oil will reduce the engine's power output. When the engine is running, the crankshaft and connecting rod big end move rapidly, and too much oil will cause intense agitation of these components. 3. It will increase the amount of oil splashed onto the cylinder walls, leading to oil burning and exhaust issues. 4. It will create resistance to the rotation of the crankshaft. 5. It will reduce the lifespan of oil seals, causing engine oil leaks. 6. It will worsen exhaust emissions and affect the lifespan of the catalytic converter.
11
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.