Are Rear Bumpers All Made of Plastic?

How to Troubleshoot When the Engine Fault Light Comes On?

When the engine fault light comes on, it indicates the following situations: a yellow symbol light indicates a fault in the engine; a red symbol light indicates a serious fault in the engine. Here is more information about the engine fault light: 1. Elimination method: Simply remove the fuse. 2. Solutions for when the engine fault light comes on: (1) Clean the engine: Once the engine fault light comes on, the owner should promptly clean the carbon deposits in the engine. (2) Improve fuel quality. (3) Use higher-grade gasoline: After cleaning the engine, the owner can choose to use 95 or 97 octane gasoline.

13

4

Share

Should You Release the Handbrake or Shift Gears First When Starting an Automatic Car?

When starting an automatic car, you should shift gears first and then release the handbrake. Below is relevant information about automatic transmission vehicles: 1. Working Principle: Automatic transmissions primarily rely on the hydraulic transmission principle of torque converters to complete gear shifts; the vehicle automatically selects the appropriate gear based on driving speed and traffic conditions, making gear shifts safer. 2. Advantages of Automatic Transmissions: Automatic transmissions use a torque converter to replace the clutch in manual transmission cars, so there's no need for frequent gear shifting. In terms of operational convenience, automatic transmissions are more suitable for beginners.

13

2

Share

How to Solve Excessive Engine Noise During Acceleration?

Here are the specific causes and solutions for excessive engine noise during acceleration: 1. Dirty throttle valve: When encountering loud engine noise during acceleration, the throttle valve should be considered first. If the throttle valve is dirty, this situation may occur, and cleaning the throttle valve once can be considered. 2. Intake manifold leakage: Unwanted air, gasoline vapor, or exhaust gas entering the intake manifold can cause the air-fuel mixture to be too rich or too lean, leading to loud engine noise during acceleration; consider sending it to a 4S shop for inspection and repair. 3. Abnormal spark plugs: Problems with the ignition coil or spark plugs in the ignition system may also cause such a situation. Check if the spark plugs are clogged, and timely replacement can improve this situation. 4. Damaged oxygen sensor: The oxygen sensor in the intake and exhaust system may sometimes be damaged, causing inaccurate intake data and also resulting in loud engine noise during acceleration, requiring it to be sent to a 4S shop for inspection and repair.

3

1

Share

What Vehicles Can an E License Drive?

An E driver's license is for ordinary two-wheeled motorcycles and the vehicle types permitted by an F driver's license. Below is more information about the E license: 1. Test content: Subject 1 (full score of 100, passing score of 90), Subject 2, Subject 3 (on a straight line with three poles, requiring an S-shaped maneuver around the three poles and then back, during which the feet must not touch the ground, the vehicle must not stall, and the vehicle must not cross the yellow line.), Subject 4 (mainly tests the recognition of road signs, traffic police hand signals, and how to handle various situations when riding a motorcycle, etc.). 2. Age requirement: Must be 18 years or older and under 70 years old.

10

4

Share

What are the causes of transmission system failure?

Transmission system failures are mainly caused by: 1. Abnormal speed in hydraulic transmission systems: For faults caused by speed abnormalities, it is necessary to individually adjust variable structures such as throttle valves, relief valves, variable displacement pumps, and speed control valves, then compare their speed range values with technical reference values for analysis. 2. Abnormal operation in hydraulic transmission systems: For faults caused by operational abnormalities, it is required to observe the operating status of relevant system actuators, determine whether they are functioning normally based on their status, identify malfunctioning directional control valves, and subsequently inspect travel control to locate the abnormal areas in the hydraulic transmission system. 3. Abnormal pressure in hydraulic transmission systems: To determine if faults are caused by pressure abnormalities, use a pressure gauge to measure the pressure values at reserved pressure test points on the system pipelines. By analyzing the difference between the measured values and standard values, the fault location causing abnormal pressure in the hydraulic transmission system can be identified.

8

5

Share

What was the original name of the truck scaina?

The original name of the truck scaina is Scania (SCANIA). The following is a related introduction to the truck scaina: 1. Appearance characteristics: Scania trucks have completely broken away from the traditional image of square, dull-looking trucks, exuding a sense of the times everywhere. Scania offers a variety of different specifications of cabs to choose from. Due to the adoption of standardized and modular design concepts, the operation of various cabs has become extremely simple, which not only reduces costs but also facilitates corresponding adjustments based on market demand. 2. Vehicle purpose: Mainly used for heavy-duty transportation, participating in railway construction transportation or engaged in log transportation, etc., it is a type of heavy-duty cargo truck.

14

4

Share

Are Rear Bumpers All Made of Plastic?

How to Troubleshoot When the Engine Fault Light Comes On?

Should You Release the Handbrake or Shift Gears First When Starting an Automatic Car?

How to Solve Excessive Engine Noise During Acceleration?

What Vehicles Can an E License Drive?

What are the causes of transmission system failure?

What was the original name of the truck scaina?

Does a car in its sixth year need to go through the inspection line?

How to Determine When the Throttle Body Needs Cleaning?

How to Prevent Theft of External Tire Pressure Monitoring Sensors?

How to Book Training for Subject 2?