Are Highway Ramp Cameras for Speed Detection?

1 Answers
OValentina
07/28/25 3:06pm
Highway ramp cameras are not for speed detection. Below are the purposes of these cameras: 1. Traffic Monitoring: Some ramp cameras are installed not to record violations but to monitor traffic flow. During peak hours, these areas experience high traffic volumes, necessitating monitoring. Drivers tend to follow rules more carefully when they see cameras, which can help prevent accidents. This explains why many ramps don't have cameras, while certain specific sections do. 2. Violation Control: Although traffic regulations clearly prohibit overtaking on ramps, some drivers still attempt to do so when entering. Cameras help deter such violations.
Was this review help?
15
4
Share
More Forum Discussions

Which Mazda vehicles use rotary engines?

Mazda RX series vehicles use rotary engines, which employ triangular rotor rotational motion to control compression and exhaust. Here are the details about Mazda RX: 1. Body dimensions: The 2008 Mazda RX8 manual model measures 4460 mm in length, 1770 mm in width, and 1340 mm in height, with a wheelbase of 2700 mm, a fuel tank capacity of 65 liters, and a curb weight of 1406 kg. 2. Vehicle configuration: The 2008 Mazda RX8 manual model is equipped with a 1.3L naturally aspirated engine, delivering a maximum power of 170 kW at 8200 rpm and a maximum torque of 211 Nm at 5500 rpm.
2
2
Share

What is the strip below the car door called?

The strip below the car door is called a scuff plate or welcome plate. The scuff plate is an automotive accessory used to decorate the door sill area, serving to protect the vehicle body and enhance its appearance. The installation method for scuff plates is as follows: 1. Remove the double-sided tape on the back of the plate and clean the surface; 2. Before pasting, position the scuff plate on the desired installation area and adjust it properly; 3. Once the position is determined, remove the red protective film and paste it. The car door consists of the door body, door accessories, and interior trim panel. Its functions are: to provide access for the driver and passengers, isolate external disturbances, and to some extent, mitigate side impacts to protect the occupants.
9
2
Share

When to Use Hazard Warning Lights?

Hazard warning lights can be used in the following situations: 1. Driving in foggy weather. Due to poor visibility in foggy conditions, not only should the hazard warning lights be turned on, but the fog lights should also be activated to alert passing vehicles and provide illumination for yourself. 2. When a vehicle breaks down or is involved in a traffic accident on the road, the hazard warning lights should be turned on to alert passing vehicles to drive safely. On highways, if a vehicle breaks down or is stopped due to an accident, failure to use the lights and set up warning signs as required will result in a 12-point penalty. 3. When towing a malfunctioning motor vehicle, both the towing vehicle and the towed vehicle should turn on the hazard warning lights to indicate that the vehicle is in an abnormal state.
8
1
Share

What is the function of a motorcycle tensioner?

The function of a tensioner is to guide and maintain tension, ensuring it always remains in the optimal tension state. Below is an introduction to tensioners: 1. Working Principle: A tensioner is a commonly used retaining device in belt and chain transmission systems. Its characteristic is to maintain appropriate tension in belts or chains during transmission, thereby preventing belt slippage or avoiding timing belt teeth from skipping or disengaging. It also prevents chain loosening or detachment and reduces wear on sprockets and chains. 2. Features: In terms of effectiveness, tensioners with spring structures are simple in design and inexpensive, making them widely used. Tensioners with rubber components, due to rubber's excellent elastic properties, have a longer lifespan than spring tensioners. However, they require higher-performance rubber, making them more expensive and less commonly used, typically found in high-end mechanical equipment.
7
1
Share

What does 88V on tires mean?

Tire 88 refers to the load index, and V refers to the speed rating, with a maximum speed of 240km/h. Tires are one of the most important components of a vehicle, and their main functions are: 1. To support the entire weight of the vehicle, bear the load of the car, and transmit forces and moments in other directions. 2. To transmit traction and braking torque, ensuring good adhesion between the wheels and the road surface to improve the vehicle's power performance, braking performance, and passability; working together with the vehicle suspension to mitigate impacts during driving and dampen the resulting vibrations. 3. To prevent severe vibrations and premature damage to vehicle components, adapt to the high-speed performance of the vehicle, reduce driving noise, and ensure driving safety, handling stability, comfort, and energy efficiency.
17
5
Share

What are the signs indicating it's time to replace car tires?

Signs indicating it's time to replace car tires include: 1. Tread wear indicators becoming flush with the tread; 2. Cracks due to aging; 3. Bulges caused by broken cords inside the tire; 4. Frequent tire repairs. Methods for maintaining tires include: 1. Regularly removing debris from tread grooves; 2. Periodically checking tire pressure; 3. Inspecting tire wear and replacing them promptly. The functions of tires are: 1. Direct contact with the road surface, working with the car's suspension to cushion impacts during driving; 2. Ensuring good ride comfort and smooth driving; 3. Maintaining excellent adhesion between the wheels and the road surface, improving traction, braking, and passability; 4. Supporting the weight of the vehicle.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.