Application Range of Gear Oil 85w140?

What are the engine speed regulations for Subject 3?

There are no explicit regulations specifying the exact engine speed requirement for Subject 3, but one of the deduction items is "speed and gear mismatch." For example, if the current speed is 40-60 km/h while still in 3rd gear, it will be judged as a speed and gear mismatch, and the engine speed will also be relatively high at this time. The following is an introduction to Subject 3: 1. Introduction 1: Subject 3 includes the road driving skills test and the safety and civilized driving knowledge test. It is part of the motor vehicle driver's license assessment and is the abbreviation for the road driving skills and safety and civilized driving knowledge test subjects in the motor vehicle driver's test. 2. Introduction 2: The content of the road driving skills test varies for different types of vehicles eligible for driving. The road driving skills test for Subject 3 generally includes preparation before getting on the car, simulated light test, starting, driving in a straight line, shifting gears, changing lanes, parking by the roadside, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school zones, passing bus stops, meeting vehicles, overtaking, making U-turns, and driving at night. 3. Introduction 3: The safety and civilized driving knowledge test generally includes the requirements for safe and civilized driving operations, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations such as tire blowouts, and knowledge of handling after traffic accidents.

14

5

Share

Why does the car feel less powerful after modifying the exhaust?

After modifying the exhaust, the exhaust pipe diameter is usually increased to allow smoother exhaust flow. Some exhaust systems are straight-through, some have backpressure, and some come with valves. Straight-through exhausts, due to the lack of backpressure or minimal backpressure, may lose some low-end torque, with straight-through systems losing relatively more. However, smoother exhaust flow can increase power at high speeds. This is why valve systems were developed—to minimize low-end torque loss while increasing power at high speeds when the valves are open. More related information is as follows: 1. Function: The exhaust pipe primarily serves to reduce vibration and noise (muffling) and minimize harmful gas pollution. During driving, exhaust gases exit the engine at high pressure, creating significant noise. The exhaust pipe contains a muffler, which helps reduce noise. The car's exhaust system also includes a "three-way catalytic converter," which reduces pollution. This device converts harmful gases such as carbon monoxide, hydrocarbons, and nitrogen oxides from car exhaust into harmless carbon dioxide, water, and nitrogen through oxidation-reduction reactions, thereby purifying the exhaust and reducing air pollution. 2. Note: Although the exhaust pipe is not a precision component inside the car and is exposed externally, many people assume it must be a durable part. As a result, even if it's covered in dirt, it may be considered normal. However, a crucial point is that the exhaust pipe connects external elements to the car's interior, primarily by expelling exhaust gases from the engine. Improper driving can allow harmful substances to enter the car's interior through the exhaust pipe. Therefore, maintaining the exhaust pipe is, in many ways, equivalent to maintaining the car's interior.

16

2

Share

What Causes the ABS Light to Illuminate in a Magotan?

ABS light illumination can occur in various states, with different causes and solutions for each state, as detailed below: State 1: ABS warning light remains constantly illuminated (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control module from determining the vehicle speed and calculating the wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the contaminants from the wheel speed sensor and adjust the gap between the sensor and the tone ring to restore normal function. Cause 2: Poor signal quality due to loose connections in the system wiring or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As engine speed increases, the voltage rises, causing the ABS indicator to turn off. This may also occur if the ABS system's power supply voltage is too low, such as due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains illuminated after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS control module malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR control module. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS control module detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and use a finger to push the brake switch linkage fully downward, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary. If the ABS warning light is illuminated, it is advisable not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

8

3

Share

What Causes the ABS Light to Illuminate in a Santana?

There are various states of the ABS light being on, with different causes and solutions for each state, as detailed below: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and the wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections between system lines or poor contact in the ABS relay, leading to system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, causing the ABS indicator light to turn off. The ABS system power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS computer malfunction. Solution: Loosen and then retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary. Check if the connector gap has widened. Replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant difference between the rear and front wheel speed signals. Incorrect tire or wheel rim specifications may also be a factor. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and push the brake switch linkage down fully with your finger. Release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary. If the ABS warning light is on, it is recommended not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's trajectory, posing significant safety risks.

18

5

Share

Do I Need to Press the Auto Hold Button Every Time?

Auto Hold function remains activated once turned on in some car models, while in others it requires manual activation after each engine restart, depending on the specific vehicle model. Here are the relevant details: 1. Operating Steps: After pressing the Auto Hold function button, each time the vehicle comes to a complete stop by braking, an indicator light will illuminate on the dashboard. At this point, there's no need to keep pressing the brake pedal as the system automatically maintains braking. The system will deactivate upon pressing the accelerator pedal. 2. Function: Auto Hold is designed to prevent unnecessary vehicle movement without requiring the driver to maintain prolonged braking or manually engage the electronic parking brake.

2

0

Share

How many driver's licenses can be used for demerit points on one vehicle

A vehicle can only use three different driver's licenses for demerit points, and the license holder must personally present the license for point deduction. Here is relevant information: Scoring cycle: If a motor vehicle driver's demerit points do not reach 12 within a scoring cycle and all fines have been paid, the points will be cleared; if the points do not reach 12 but there are unpaid fines, the points will carry over to the next scoring cycle. If 12 points are deducted within one scoring cycle, the driver must pass the subject one test after studying at the issuing vehicle management office or the local traffic violation office to clear the full-point record and restore normal use of the driver's license.

2

Share

Application Range of Gear Oil 85w140?

What are the engine speed regulations for Subject 3?

Why does the car feel less powerful after modifying the exhaust?

What Causes the ABS Light to Illuminate in a Magotan?

What Causes the ABS Light to Illuminate in a Santana?

Do I Need to Press the Auto Hold Button Every Time?

How many driver's licenses can be used for demerit points on one vehicle

Is the Leiling Hybrid a Three-Cylinder or Four-Cylinder Engine?

What does it mean when there is only one motor vehicle lane in the same direction?

What is the engine oil specification for the Wildlander Hybrid 2.5 Luxury Edition?

Where is the memory card for Cadillac dash cam located?