Analysis of Wuling Hongguang Mini Malfunction Indicator Lights

1 Answers
DiEllie
07/30/25 4:46am
Analysis of Wuling Hongguang Mini malfunction indicator lights is as follows: 1. Poor-quality gasoline: This is usually caused by filling up with substandard gasoline at non-compliant gas stations, resulting in incomplete combustion of the air-fuel mixture during engine operation and triggering the engine malfunction light. While this does not affect driving safety, it may cause some degree of harm to the engine. 2. Oxygen sensor failure: Modern vehicles are equipped with two oxygen sensors, one before and one after the three-way catalytic converter. The front oxygen sensor detects the air-fuel ratio under different engine operating conditions, and the ECU adjusts fuel injection and calculates ignition timing based on this signal. The rear sensor primarily monitors the performance of the three-way catalytic converter. Therefore, if the oxygen sensor is damaged or the sensor connector is faulty or loose, it may cause the air-fuel mixture to become too lean or too rich, leading to the illumination of the malfunction indicator light.
Was this review help?
15
4
Share
More Forum Discussions

Where to add windshield washer fluid for the Hongqi H5?

Windshield washer fluid filling location: Pull the engine compartment lever in the driver's cabin to open the engine hood, locate the windshield washer fluid filler port, and fill it with purchased washer fluid. Generally, windshield washer fluid does not require dilution, but some products may need it—refer to the instructions. The functions of automotive windshield washer fluid are as follows: 1. Cleaning performance: Windshield washer fluid typically has wetting, penetrating, and solubilizing functions, thereby serving to clean and remove dirt. 2. Anti-freeze performance: The presence of alcohol and ethylene glycol can significantly lower the freezing point of the liquid, thus providing anti-freeze effects and quickly dissolving frost.
16
2
Share

Where is the Cabin Air Filter of Chery Flagcloud 2 Located?

Flagcloud 2's cabin air filter is located beneath the cover panel under the front windshield. Below is extended information about replacing the cabin air filter: 1. If the airflow from the AC is significantly reduced, the cabin air filter may be clogged. First, clean the filter or replace it if necessary. 2. The cleaning frequency depends on road conditions, and early cleaning is recommended. 3. The cabin air filter should be correctly installed in its position. Using the AC without the filter may degrade dustproof performance and affect AC performance. 4. In cities with poor air quality, it is recommended to replace the cabin air filter twice a year.
3
4
Share

What is the reason why the xrv electronic handbrake cannot be released when there is no power?

Generally, there are two situations when the handbrake has no power: 1. If the car cannot start due to a dead battery, first press the brake pedal to prevent the vehicle from moving, and then call for help. 2. If the power is cut off after the handbrake is activated, the brake will remain locked and will not release. In this case, you need to find someone to charge the battery and then restart the car. The following are the correct ways to use the electronic handbrake: 1. When parking, simply press the brake pedal to keep the vehicle stationary, shift the gear to P, and finally press the function button of the electronic handbrake. 2. When restarting, shift the gear to D, and the electronic handbrake will be released after pressing the accelerator.
3
2
Share

How to Reset the Polo Maintenance Reminder?

polo maintenance reminder reset method is: 1. Insert the car key but do not turn it yet. Firmly press the odometer reset button located below the speedometer and keep holding it during subsequent operations. 2. While holding the reset button, turn the key to the self-check position (do not start the engine), still maintaining pressure on the reset button. 3. Continue holding the reset button for over 10 seconds, then release to successfully reset. 4. Additional information: The maintenance light is a manufacturer-set reminder function that alerts owners when scheduled maintenance is due based on mileage or time intervals, displayed through instrument panel messages or indicator lights.
16
0
Share

How to Remove the Thermostat of Nissan Teana?

The replacement steps for the Teana thermostat are as follows: 1. Turn off the engine and open the front hood. Disconnect the negative terminal of the battery to prevent the electric fan from suddenly operating during work, which may cause personal injury. 2. Remove the plastic cover outside the timing belt and the engine assembly. The location of the generator will affect the replacement of the thermostat, so the generator assembly needs to be removed. 3. Place a water tray under the car, then prepare to remove the water pipe and wait for the antifreeze to drain completely. 4. Remove the faulty thermostat and install the new one. After installing the thermostat, apply a layer of sealant to the water pipe area. 5. Reinstall the removed water pipe, generator, and timing plastic cover to their original positions. Reconnect the negative terminal of the battery, add new antifreeze, and then test drive the car.
20
2
Share

What does TC mean in cars?

TC in cars stands for the Traction Control system. When the TC light appears on the dashboard, it indicates that the vehicle's Traction Control system is active. This system is designed to enhance driving stability, especially for rear-wheel-drive vehicles. Below is an introduction to the Traction Control system: 1. The Traction Control System, also known as the Anti-Slip Regulation (ASR) system, prevents wheel slippage when braking on slippery surfaces, which could otherwise lead to loss of directional control. Similarly, during acceleration or sudden acceleration, drive wheels may slip, posing a risk of losing control, particularly on icy or slippery roads. 2. The Traction Control System utilizes electronic sensors to detect when the driven wheels' speed is lower than that of the drive wheels. Upon detecting such a condition, it sends signals to adjust ignition timing, reduce throttle opening, decrease fuel supply, downshift, or apply brakes to the wheels, thereby preventing further wheel slippage.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.