Share

On April 26, 2026, India’s human spaceflight program is in its final stretch — and one of the trickiest engineering challenges is making sure astronauts come back down in one piece. A spacecraft returning from orbit can’t use fuel to land. It relies on atmospheric drag to shed most of its velocity, then needs parachutes to make the last braking safe. For ISRO’s Gaganyaan crew module, the parachute system is not just a single canopy: it is a carefully staged, deliberately redundant cluster of chutes that must inflate in the middle of turbulent airflow, survive intense heat and shock, and still land gently enough to protect the crew. Here is how that system works, and why every layer of it exists.
Most crewed spacecraft do not rely on one giant parachute. They use a coordinated sequence of pilot, drogue, and main canopies. The pilot chute comes out first; it is a small chute whose job is to pull out either a larger drogue or the main canopy. The drogue chute opens early in the descent, often while the module is still moving fast, and it does two jobs: it stabilises the capsule and starts removing speed. Only after the capsule has been slowed down does the main parachute deploy, with its much wider canopy providing the final “soft landing” deceleration.
This sequence is important because the descent profile is extreme. When the Gaganyaan crew module enters the lower atmosphere, it will still be moving at roughly 170 metres per second — faster than a Formula 1 car. No single parachute designed for crewed flight can absorb all that energy at once.
The crew module is a blunt-shaped vehicle, and that shape has consequences for parachute deployment. As the capsule falls, it creates a powerful turbulent wake behind it. A parachute packed into a bag at the rear of the module has to be ejected through that wake and open in the region beyond it, where the air is moving more uniformly. If the chute doesn’t have enough energy to cross that turbulent zone quickly, it can tangle, fail to inflate, or collide with the capsule.
That’s why deployment mechanisms matter. Three conventional methods are used by recovery engineers. A static line uses a physical tether attached to an aircraft or a fixed point; as the payload falls away, the tether pulls the parachute out. Drogue guns fire a mass at high speed, and the momentum of that mass yanks the parachute through the wake. Mortars work in a similar way, using a pyrotechnic charge to create expanding gas that throws the packed parachute bag away from the module. The mortar is especially useful because it gets the canopy clear of the wake quickly and reduces the chance of entanglement.
All of this happens only after the capsule has slowed to subsonic speed. At supersonic speeds, standard canopies would encounter shockwave interactions and dynamic pressure so intense that the fabric would likely be shredded.
Imagine trying to open a large umbrella in the middle of a storm and snapping it open all at once. The wind may overturn it. A crew parachute faces a much harsher version of the same problem, but with the added consequence that failure could be lethal.
If a fully open main parachute were connected to a capsule moving at high speed, the instantaneous opening shock would be enormous. The canopy fabric could tear, and the crew would be subjected to a deceleration spike far above acceptable limits. The solution is to increase the diameter of the parachute in steps. Each stage removes some speed and pressure, so by the time the next, larger stage opens, the conditions are manageable. Multi-stage release is therefore not a luxury; it is a fundamental part of making crewed parachutes survivable.
In large parachutes, “reefing” is the technique used to prevent the canopy from blooming fully at the moment of deployment. A strong cord runs through the skirt of the canopy, and the length of that cord determines how much of the canopy is allowed to open in the first step. Think of it as pulling the fabric down to the bottom of an umbrella and opening it only a little. Attached to the cord is a reefing line cutter — a small, rugged tube containing a blade and a chemical timer. After a pre-set time, the cutter fires, severs the cord, and lets the canopy open to its full size. This technique avoids both structural failure and dangerous deceleration spikes.
Testing a parachute that has to work without fail is harder than deploying it. Ground-based tests often use a Rail Track Rocket Sled, a sled pushed along rails by small solid rocket motors. Once the sled reaches the required velocity, the parachute is deployed from it. India’s Terminal Ballistic Research Laboratory in Chandigarh operates one of these facilities, giving ISRO a way to test chutes without leaving the ground.
Other test methods include dropping a test article from a helicopter or fixed-wing aircraft, or using a rocket-powered test vehicle to carry the module to altitude and release it. These tests are designed to simulate conditions as closely as possible before any actual crewed flight.
Aerospace parachutes have to balance three conflicting needs: high tensile strength, heat resistance, and low mass. The materials chosen for the Gaganyaan parachute system reflect those requirements. Nylon is the workhorse of modern canopies because it has enough elasticity to absorb the sudden shock of inflation, and it can be packed tightly into a small volume. Kevlar is used for suspension lines and structural reinforcement because of its exceptional strength and heat resistance. Nomex, another high-performance material, protects areas exposed to hot mortar gases and frictional aerothermal heating.
This is not ordinary fabric work. The entire parachute system is packed under high pressure to save space inside the crew module, which means the materials must also survive years of storage and sudden, forceful deployment without degrading.
ISRO’s qualification field for this work is the Aerial Delivery Research and Development Establishment in Agra, a laboratory under the Defence Research and Development Organisation. The Gaganyaan crew module is configured with two drogue parachutes deployed by mortars and three main parachutes, which are themselves deployed by pilot chutes fired from mortars. The redundancy is deliberate: if one main parachute develops a major anomaly, the other two independent chains are designed to be sufficient to ensure a safe touchdown.
The system also has to consider what happens after landing. Once the module touches down — on land or in water — the parachute cannot stay attached. Wind blowing across the canopy can drag the module along the ground or flip it over in the sea. Pyro cutters or mechanical quick-release devices are therefore activated to disconnect the parachute from the module immediately after touchdown, protecting the astronauts from being dragged or capsized.
ISRO has said its first uncrewed Gaganyaan mission is targeted for 2026, and the recovery system is among the key elements being qualified in the run-up to that flight. The uncrewed mission is expected to validate many of the systems on board, including the parachute deployment sequence, before astronauts climb into the spacecraft. India’s astronaut training programme is already underway, and the recovery hardware will go through further integrated tests and simulated failure scenarios in the months ahead.
Every layer of the Gaganyaan parachute system — the pilot chutes, drogue chutes, main canopies, reefing cords, cutters, and release mechanisms — exists for one reason: to make the final stage of an orbital flight as safe as a landing can be. For ISRO, that’s not just an engineering problem. It’s the difference between bringing the crew home and a tragedy.









