···
Log in / Register

Why is the car's reverse light always on?

3 Answers
Reese
09/06/25 3:56am
If the car's reverse light stays on, it may be due to the switch not being turned off or a fault in the reverse light circuit. Here is some related knowledge about car lights: 1. Function: Car lights are various traffic lights installed on vehicles to ensure safe driving, divided into two categories: lighting lights and signal lights. 2. Classification: Headlights, fog lights, reverse lights, license plate lights, dome lights, instrument panel lights, and trunk lights. 3. Precautions: Checking car lights is one of the simpler steps in all new car inspection procedures, but since the installation of car lights is relatively prone to issues during the overall vehicle assembly process, it is essential to take this step seriously during inspection.
Was this review help?
18
4
Share
LaAbel
09/18/25 3:52am
After driving for so many years, I've encountered the issue of the reverse lights always staying on. Usually, it's due to a faulty reverse light switch. That little component is installed near the transmission and should activate when shifting into reverse gear. However, if it gets stuck or wears out, the light remains on. A short circuit in the wiring can also be the culprit, such as when rainwater seeps into the connector, causing the circuit to connect and the light to stay on foolishly. When checking, first turn off the car and see if there's anything stuck in the gear lever. Then test if the fuse is okay. If everything seems fine, it's likely the switch's problem, and replacing it with a new one costs just a few dozen bucks. Don't delay fixing it, or the battery will drain quickly, causing major trouble when you need to drive. I replaced the switch myself last time—it was quite simple, even a beginner can try it, but remember to wear gloves to prevent electric shocks.
Was this review help?
2
5
Share
Expand All
Samuel
11/01/25 4:18am
My old car's reverse light keeps staying on, which is quite alarming. Turns out it was because too much clutter behind the gear lever was pressing against the switch. When the switch gets stuck, the light won't turn off, and aging wiring often causes short circuits leading to similar issues. The solution is simple: first clear out the clutter and test if the light goes off. If it doesn't, then you need to check the wiring. If there's a short circuit in the wires, the current can go haywire and potentially damage other components, so get it fixed ASAP. I've been through this once—it almost caused an alternator failure. Luckily, I took it to the repair shop early and got it fixed for a small cost. Remember not to pile stuff near the gear lever while driving to avoid such mishaps in the future.
Was this review help?
2
2
Share
Expand All
More Forum Discussions

How to Deal with Glue Residue After Removing Window Tint Film?

Methods for handling residual adhesive from car window tint film are as follows: 1. The leftover adhesive from car window tint film can be wiped off using makeup remover oil or asphalt cleaner; 2. You can also use polyurethane thinner, commonly known as 811 cleaner, for wiping; 3. Lastly, another method is to use essential balm, which has fast volatile properties and low cost. Removing car window tint film requires certain steps and techniques, detailed as follows: 1. Peeling the film: First, lift a corner of the car window tint film, preferably using a fingernail or adhesive tape. If that doesn't work, consider using a blade to peel it. 2. Removing the film: With the help of hot air from a heat gun or hairdryer, use appropriate force and speed to slowly peel off the car window tint film. 3. Removing adhesive: If there is any residual adhesive from the glass film after peeling, clean it off with adhesive remover or cleaning agent.
1
2
Share

What are the causes of Camry idle vibration?

Camry idle vibration may be caused by the following reasons: 1. Severe engine carbon deposits - The most common cause of car vibration is dirty throttle valves or excessive carbon buildup in fuel injectors. When there's too much carbon deposit inside the engine, the gasoline sprayed by cold start injectors will be largely absorbed by these deposits; 2. Engine misfire - This mainly refers to one or more cylinders not working properly, manifested as: intermittent exhaust gas flow with noticeable exhaust pipe vibration, obvious engine vibration that can be felt, sometimes accompanied by "popping" sounds. This is mostly related to ignition coil failure; 3. Uneven air-fuel mixture in the engine can also cause idle vibration after cold start. The lower the temperature, the more fuel required for cold start, and the presence of carbon deposits will significantly affect whether cold start proceeds smoothly.
3
4
Share

Does idling the car with the heater on cause damage to the vehicle?

Idling the car with the heater on does not cause damage to the vehicle as long as the engine reaches its normal operating temperature. However, if the heater is turned on while the engine is still cold and has not reached its normal operating temperature, it can slow down the engine's warming process, leading to increased fuel consumption. Nevertheless, this does not harm the car. Below is some relevant information: 1. The fuel consumption when using the heater during idling depends on the car's displacement and engine tuning. For household cars, idling with the heater on for one hour consumes approximately 1 to 2 liters of fuel, though this may vary depending on the car model. 2. While idling with the heater on does not cause serious damage to the car, it can affect the passengers inside. Since the fuel does not burn completely during idling, carbon monoxide is produced. If the windows are not opened, the concentration of carbon monoxide inside the car can gradually increase, potentially leading to carbon monoxide poisoning for the passengers.
5
2
Share

Can I use my original license plate when changing to a new car?

When changing to a new car, you can retain your original license plate. For car owners who wish to keep their original plate, it is essential to ensure that the original plate has been used for more than one year. Only then will the plate be retained under the original owner's name during the transfer process. The retention period is one year. If the owner does not apply to reuse the plate within this period, it will automatically expire after one year, and the vehicle management office will reclaim the plate, making it unavailable for future use. The required documents for changing the car without changing the plate are as follows: 1. "Motor Vehicle Transfer or Registration Application Form"; 2. Original and copy of the owner's ID card; 3. Proof of vehicle purchase tax payment or tax exemption certificate, vehicle annual inspection certificate, and relevant documents submitted during vehicle registration; 4. Non-local residents also need to bring a residence permit and proof of the vehicle's origin; 5. For imported vehicles, additional documents include import certificates, vehicle whole-vehicle factory qualification certificate, and compulsory traffic insurance certificate.
7
5
Share

Should the tire pressure be the same for front and rear wheels of a sedan?

Front tire pressure and rear tire pressure can be different, but the difference should not be too large. Tire pressure is a range, not an exact value. In certain specific situations, it is more appropriate for the rear tire pressure to be higher than the front tire pressure. Below is relevant information: 1. For example, when the rear seats are fully occupied by three people and the trunk is also loaded with many items, the rear tire pressure should be higher than the front tire pressure. Higher rear tire pressure can make the car more fuel-efficient, resulting in lower fuel consumption. Additionally, the car can accelerate faster. The principle is: the higher the tire pressure, the smaller the contact area between the tire and the ground; the lower the tire pressure, the larger the contact area. 2. The front wheels are not only the driving wheels but also the steering wheels. If the front tire pressure is higher, the wear on the front tires will increase. Both the front and rear tire pressures must be within the standard range, and the difference should ideally not exceed 0.1bar.
18
5
Share

Is 0W40 Oil Suitable for All Seasons?

0W40 engine oil is considered all-season oil, but its suitability still depends on the temperature of the location where the vehicle is used. The 0W designation indicates the oil's cold-start performance—the smaller the number, the better the oil's cold resistance. Therefore, using 0W40 oil allows for easy engine starts even in cold weather. The number 40 represents the kinematic viscosity standard at 100°C (between 12.5mm²/s and 16.3mm²/s). Additional information: 1. In fact, many modern engine oils are designed for both winter and summer use, primarily depending on the oil's quality grade and performance. If the engine frequently operates under high-load conditions (accelerating oil consumption), it is advisable to use full synthetic or semi-synthetic oil. 2. As for quality grades, following the level specified in the vehicle's manual is generally sufficient for daily use. However, if the vehicle is often driven in congested urban environments, upgrading to a higher-grade oil (more environmentally friendly and economical) may be considered.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.