Where is the airbag control module located in the Lavida?

2 Answers
Dave
08/28/25 8:38am
In front of the gear shift lever or beneath the gear lever. Below are detailed introductions about airbags: 1. Areas marked with AIRBAG on the vehicle indicate airbag locations. Use a diagnostic tool to detect faults in the airbag system and perform repairs accordingly. 2. The airbag system is a passive safety protection system (see vehicle safety performance) that, when used in conjunction with seat belts, provides effective collision protection for occupants. 3. During vehicle collisions, airbags can reduce head injury rates by 25% and facial injury rates by approximately 80%. 4. The system mainly consists of airbag sensors, collision airbags, and electronic control units. 5. The driver-side collision airbag is installed in the steering wheel; the passenger-side collision airbag is typically mounted on the dashboard. 6. Airbag sensors are installed on the left, right, and center of the cabin partition; the central airbag sensor and airbag system are integrated with the electronic control unit. 7. Airbag components primarily consist of the airbag itself, a gas generator, and an igniter. 8. The electronic control unit is responsible for data collection, processing, diagnosing airbag reliability, ensuring timely ignition signal transmission when preset values are reached, precisely timed ignition, and providing sufficient driving current for the gas generator.
Was this review help?
20
4
Share
DelKiara
09/10/25 6:44am
I've encountered a similar issue before. When driving an older Lavida model, the airbag warning light came on. The airbag control module is usually hidden under the passenger seat or beneath the center console near the gear lever, with the exact location varying by model year. Handle with care – always disconnect the vehicle's negative battery terminal before removal to prevent accidental airbag deployment, as the sensors inside are highly sensitive. The module might be concealed under carpeting or trim panels, and a simple inspection with a screwdriver to remove the relevant panel should reveal it. If attempting DIY repairs, take precautions against static electricity and avoid getting the module wet, as this could cause short circuits leading to system malfunctions. Remember, the airbag system is crucial for driving safety. If unsure, it's best to consult the professional repair manual at a 4S dealership – it took me some time to figure it out myself. During routine maintenance, regularly check under the carpets to ensure nothing is stuck there, and keeping the area clean can also extend the module's lifespan.
Was this review help?
10
2
Share
Expand All
More Forum Discussions

Will covering the license plate be captured by electronic police?

It will be captured by electronic police. Deliberately covering the license plate is mainly to avoid being captured by surveillance cameras, which can also prevent being detected by electronic eyes, leading to some violations not being recognized. However, if caught by traffic police, covering the license plate will result in a 12-point deduction, and if there are any violations, corresponding penalties will also apply. Below are relevant details: Relevant penalties: According to the "Road Traffic Safety Law of the People's Republic of China," for deliberately covering or defacing a motor vehicle license plate, the public security traffic management department will issue a warning or impose a fine ranging from 20 to 200 yuan, with a 12-point deduction. Reasons like rain or snow: Additionally, for cases where the vehicle body or license plate is covered by mud due to rain, snow, or road conditions, or where the license plate recognition is affected by cargo on a truck, the traffic management authorities will order the party to correct the situation on the spot.
2
5
Share

What Causes Shaking After Startup?

Reasons for shaking after startup: 1. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor; 2. Aging engine mounts; 3. Dirty throttle body or excessive carbon buildup in the fuel injectors, leading to an overly lean air-fuel mixture during cold starts; 4. Abnormal engine coolant temperature; 5. Low engine cylinder pressure. Engine maintenance tips: 1. If the vehicle is only driven in urban areas, the air filter may not get clogged, but if driven on dusty roads, pay special attention to cleaning the air filter; 2. Remove sludge from the throttle body; 3. Clean carbon deposits from the fuel injectors, as the combustion chamber is prone to carbon buildup, which can cause starting difficulties. Carbon deposits in the fuel injectors can also lead to clogged fuel passages, distorted fuel spray, and poor atomization.
17
1
Share

How to Set the Time on an Accord 8?

To set the time on an Accord 8: Locate the SOUND button on the center console's audio and air conditioning panel. Below the SOUND button, there is a CLOCK label. Press and hold the SOUND button until you hear a beep, and the time on the LCD display will start flashing. Then, press the 4 button to adjust the hour, the 5 button to adjust the minutes, and the 6 button to reset the minutes to zero. After setting the correct time, press the SOUND button again to confirm, and the time will stop flashing, completing the setup. The Accord 8 has a body length of 4893mm, width of 1862mm, height of 1449mm, and a wheelbase of 2830mm. The car's engine has a maximum power output of 143kW and a maximum torque of 260Nm.
9
3
Share

Is it necessary to break in a new automatic transmission car at high speeds?

Yes, here are the relevant details: Precautions for breaking in a new car at high speeds: Too light or too heavy load: When breaking in a new car at high speeds, it must be done under full load. Otherwise, the effort will be wasted. Therefore, follow the vehicle's full load mass as specified in the manual to gather enough people. If you can't find enough people, you can fill the trunk with items. Running before the first maintenance: Many beginners have little experience in how to break in a car at high speeds and lack knowledge in this area. They often think about taking the car out for high-speed runs shortly after getting it, unaware that this can cause significant harm to the new car. Therefore, breaking in a new car at high speeds should only be done after the first maintenance. This is because, after the first maintenance, all bolt torques and potential issues with fluid levels have been checked and addressed, allowing you to drive with confidence.
6
5
Share

What type of oil is generally used for the first maintenance?

Generally, mineral oil or semi-synthetic oil is used for the first maintenance, and it is recommended to change it every 5,000 kilometers or every six months thereafter. Engine oil, also known as engine lubricant, consists of base oil and additives. It serves multiple functions such as lubrication and wear reduction, auxiliary cooling, sealing to prevent leaks, rust and corrosion prevention, and shock absorption. The first maintenance of a car refers to the initial service after the vehicle leaves the factory. The primary tasks include changing the engine oil and oil filter. During this process, a comprehensive inspection of the vehicle is conducted, which includes checking all lights, fluid levels, functionality of the electrical systems, tire inspection and pressure adjustment, condition of the chassis components, and checking for leaks and proper operation of the engine and transmission.
12
3
Share

What to Do If Your Car Was Hit by an Unknown Party?

Solutions for when your car was hit by an unknown party: 1. If you can locate the other vehicle or the other party has left contact information, directly seek compensation from them, as this type of accident is entirely their fault; 2. If the other vehicle cannot be found, you can only report to the police. This is considered a hit-and-run, and the traffic police will check surveillance footage. If the other vehicle can be identified through surveillance, you can then seek compensation from them. If there is no surveillance and the other vehicle cannot be found, the police will still issue a certificate, which serves as the basis for filing an insurance claim. According to regulations, if the parties involved reach an agreement through private negotiation, the following methods can be used to fulfill compensation for road traffic accident damages: 1. The parties involved compensate on their own; 2. Go to the insurance company where the policy is held or to a road traffic accident insurance claims service location to handle the compensation matters.
20
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.