···
Log in / Register

What is the reason for the occasional idle shaking of the Cadillac XTS?

3 Answers
IvanRose
08/31/25 2:56am
The reasons for the occasional idle shaking of the Cadillac XTS are: 1. Severe engine carbon deposits: If there is excessive carbon buildup in the engine, the vehicle may exhibit symptoms such as poor engine performance, increased fuel consumption, or even difficulty starting. Over time, this can cause significant damage to the vehicle. 2. Unstable oil pressure: There are many factors that can cause unstable engine oil pressure, such as insufficient oil, dirty oil, thinning oil, oil pipe leakage, oil pump damage, or excessive wear of its components. 3. Issues with the ignition system: When certain components or circuits of the car's ignition system experience open circuits or short circuits, resulting in insufficient primary current, low secondary voltage, or failed ignition timing adjustment, it can lead to unstable engine operation, deteriorating acceleration performance, reduced power and fuel economy, and also cause idle shaking. The Cadillac XTS is a newly positioned large luxury sedan by Cadillac, featuring 20-inch 11-spoke wheels and Bridgestone tires. Components such as LED headlights and a spoiler mounted on the trunk lid showcase its all-new design style.
Was this review help?
16
3
Share
StChase
09/12/25 6:25am
I've repaired quite a few Cadillac XTS models, and occasional idle shaking is pretty common. Many owners come to me due to ignition system issues, such as aging spark plugs or poor ignition coil contact, which can lead to uneven combustion. Clogged fuel injectors may also occur, causing unstable fuel delivery and resulting in shaking. Additionally, engine mounts, once aged or damaged, can transmit vibrations to the vehicle body at idle. Sensor failures are another factor; for instance, inaccurate readings from oxygen sensors or throttle position sensors can affect the air-fuel ratio. Excessive carbon buildup can hinder combustion efficiency. If not addressed promptly, the shaking may worsen or even damage the engine. I recommend using a diagnostic scanner to read fault codes in time—avoid DIY tinkering—and visit a reliable repair shop for a thorough inspection to prevent minor issues from escalating. Regular filter replacements and carbon cleaning during maintenance can prevent most cases.
Was this review help?
7
0
Share
Expand All
Michelle
10/26/25 7:14am
After driving my Cadillac XTS for several years, I've encountered minor issues like sudden shaking during idle. Based on my experience, the most common cause is worn-out spark plugs – as mileage accumulates, ignition becomes less precise. A dirty air filter can also restrict airflow and make the engine shudder. Once, I discovered loose engine mounts during inspection, and tightening them significantly improved the situation. Aging sensors like oxygen sensors can disrupt the air-fuel mixture ratio. Regarding fuel, using low-quality gasoline leads to excessive carbon buildup; switching to premium fuel from reputable stations noticeably reduced vibrations. Personally, I find Cadillac engines somewhat sensitive – it's best not to ignore small issues. Regular oil and filter changes, along with periodic intake system cleaning, help maintain smooth idling. When shaking occurs, stay calm: first observe the frequency, then have a mechanic investigate.
Was this review help?
17
2
Share
Expand All
More Forum Discussions

How to Replace the Position Light on a Volkswagen Bora?

Volkswagen Bora uses T10 bulbs for its position lights. The steps to replace the position light are as follows: 1. First, open the hood and locate the headlight dust cover. 2. Open the dust cover to find the position light, then gently pull it out. 3. Remove the bulb from the socket and compare the two bulbs. 4. Insert the LED bulb into the socket. 5. After inserting, turn on the switch to test if it lights up. If not, remove and reverse the bulb before reinserting, as the bulb has polarity. 6. Finally, carefully install the position light back, ensuring it is properly seated.
16
5
Share

What type of USB interface does the Baojun 730 have in the car?

The Baojun 730 car USB interface is a universal interface, which can be used to plug in a USB drive to listen to music, charge mobile phones and MP3 players, serve as a USB car cigarette lighter interface, function as an interface for electronic dogs and dash cams, and charge computers and tablets. The main purpose of the USB interface in the car is to use the car's standard power supply to charge DC-5V electrical appliances via the USB interface or to serve as a fixed power interface for electrical appliances. Here are some precautions for using the car USB interface: 1. Charging should only be done when the car's engine is started to avoid damage to electrical appliances due to unstable car power supply. 2. Do not connect too many electrical appliances to avoid overloading and damaging the car battery and generator. 3. Do not use the USB interface during thunderstorms to avoid lightning strike accidents. 4. Do not use the USB interface in a humid environment, as rust or water stains may cause the USB drive to fail to connect properly.
20
5
Share

Where is the tire pressure reset switch for the Volkswagen Magotan?

The tire pressure reset switch for the Volkswagen Magotan is located on the lower left side of the multifunction steering wheel, and there is also a tire pressure reset button on the car's center console. There are three commonly used methods for tire pressure monitoring: Direct Tire Pressure Monitoring: The direct tire pressure monitoring system uses pressure sensors installed in each tire to directly measure the tire pressure. It then transmits the pressure information wirelessly from inside the tire to a central receiver module, which displays the tire pressure data. Indirect Tire Pressure Monitoring: When the pressure in a tire decreases, the vehicle's weight causes the rolling radius of that tire to become smaller, resulting in a faster rotation speed compared to the other wheels. By comparing the differences in rotation speeds between the tires, the system monitors the tire pressure. Tire Pressure Monitoring System (TPMS) Introduction: This system combines the advantages of the two aforementioned methods. It is equipped with direct sensors in two diagonally opposite tires and also includes a 4-wheel indirect system.
5
0
Share

Where is the brake light switch on the Hyundai Santa Fe?

The brake light switch on the Hyundai Santa Fe is located below the brake pedal. Brake lights are generally installed at the rear of the vehicle and feature a red-colored main body to enhance light penetration. This ensures that vehicles behind can easily detect when the front vehicle is braking, even in low visibility conditions, thereby helping to prevent rear-end collisions. Below is a classification of automotive lights: 1. Headlights: Combined headlights are located at the front of the vehicle and primarily serve illumination and signaling purposes. The light emitted by headlights illuminates the road ahead, enabling safe driving at night. 2. Taillights: Combined taillights are located at the rear of the vehicle and mainly serve illumination and signaling purposes. 3. Turn signals: These lights indicate left or right turns to other road users and are required by regulations to be amber in color. 4. License plate lights: These lights primarily illuminate the license plate, making it easier to identify the vehicle's license plate at night.
6
1
Share

How to Open the Car Engine Oil Cap?

Most car engine compartment covers are quite similar in how they are opened. Generally, there is an interior latch located below the dashboard, opposite the driver's left leg. Pulling this latch will unlock the engine compartment cover. Alternatively, you can pull a small handle extending from the grille or reach into the popped edge of the engine compartment cover to pull the latch and open it. Here are the steps to open a car engine cover: 1. First, locate the engine hood control switch below the left side of the driver's seat. 2. Then, pull the engine hood control switch upward. You will hear a 'pop' sound, indicating that the latch of the engine hood has been released. 3. At this point, step out of the car and you will notice a clear gap on the front cover of the car engine. 4. Finally, fully open the engine hood and prop up the support rod on the car engine's front cover to complete the process.
3
2
Share

What is the fuel tank capacity of the 2019 Lavida Plus?

Currently, there are 16 models of the 2019 Lavida Plus, among which the 1.5L version has a fuel tank capacity of 52.8 liters, while other versions have a capacity of 51 liters. This data is provided by the automobile manufacturer. The 2019 Lavida Plus TSI requires 95-octane fuel, while other versions use 92-octane fuel. The 1.5L version has a fuel consumption of 5.6 to 5.7L per 100 kilometers, allowing a driving range of 926 to 942km on a full tank. Other versions consume 5.3 to 5.7L per 100 kilometers, with a range of 894 to 962km on a full tank. During daily driving, it is essential to monitor the remaining fuel in the tank. This is typically done by observing the fuel gauge inside the vehicle. If there are no other issues, the fuel level will be accurately reflected on the gauge. The fuel gauge usually has 5 to 6 segments, and it is advisable to refuel when only 2 segments remain to avoid running out of fuel midway. In actual refueling, the amount of fuel may exceed the calibrated capacity. This is because the manufacturer's specified fuel tank capacity is measured from the bottom of the tank to the safety limit, with additional space from the safety limit to the tank opening. This space ensures that the fuel can expand when temperatures rise without overflowing. If fuel is added up to the tank opening during refueling, the actual amount may exceed the calibrated capacity.
9
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.