How to Remove the Bumper of Baojun 730?

[Leila]

Below is the method for removing the bumper of Baojun 730: 1. Remove the clips on the left and right inner fenders, pry open the inner fenders, and there is a screw inside each corner of the bumper. 2. You can gently pry it open, then open the hood and remove the clips on the bumper. Use a flat-head screwdriver to pry the clips from the gap to release them. 3. Remove the clips and screws underneath. Below is an introduction to the bumper of Baojun 730: 1. The car bumper is a safety device that absorbs and mitigates external impacts, protecting the front and rear of the vehicle body. 2. With the development of the automotive industry and the widespread use of engineering plastics in the automotive sector, the car bumper, as an important safety device, has also evolved.

[HectorAnn]

Last time I removed the bumper of my Baojun 730 myself to replace a small damaged section. First, I had to prepare the tools: a Phillips screwdriver, plastic pry bar, and possibly a wrench. Open the hood, and you'll see some screws securing the upper edge of the bumper, about six to eight in total—use the screwdriver to remove them one by one. Then, crawl under the car to locate the bracket bolts at the lower part of the bumper and loosen them. There are also hidden screws inside the wheel arches, so take your time to find and remove them. The bumper is held in place by plastic clips, so gently pry open the gaps with the pry bar and slowly pull it away. Be extra careful not to yank it forcefully, as the car might have radar wires or fog light wiring connected—remember to disconnect the plugs beforehand to avoid damage. During my removal, one of the clips had aged and broken, so I used a heat gun to soften it slightly before prying it open, which worked quite well. The whole process took me about 40 minutes. For beginners, I recommend taking it slow and watching some online video tutorials first. When reinstalling, align the clips properly, press them gently into place, and then tighten the screws to prevent loosening and ensure safety.

[LeBriella]

Removing the Baojun 730's bumper is actually quite straightforward once you're familiar with the process. First, ensure the vehicle is parked securely, then open the hood to remove the approximately six cross-head screws at the top of the bumper. Next, carefully locate and remove the two to three fixing screws inside the wheel arches. Also, loosen the bolts connecting the lower grille at the bottom of the car. The main body of the bumper is held by clips; gently pry them open from the gaps using a plastic pry tool, being careful not to apply too much force to avoid cracking the plastic. Pay special attention to the wiring harness—if there are connectors for front cameras or radar, disconnect them first to prevent wire damage. After removal, inspect the clips for integrity; if they're aged, have replacements ready to avoid delays. I always carry a toolkit with screwdrivers and pry bars when working on cars—the whole process can be completed within twenty minutes. However, always test all functions before reassembly to ensure driving safety.

[MacAdalynn]

Before removing the bumper, pay attention to details—I prioritize safety first. Start by disconnecting the negative battery terminal to prevent short circuits. Then proceed with disassembly in order: first loosen the screws under the engine compartment (about five), followed by the hidden screws inside the wheel arches. The bumper body is secured by clips; use a pry tool to gently separate them. Handle with care—the wiring harness of the Baojun 730, such as the reverse radar, is prone to damage, so disconnect the plugs in advance. I recommend working with a partner: one to support the bumper and the other to operate, reducing the risk of accidental scratches to the body. The simplest tools to use are a Phillips screwdriver and a clip-specific pry tool. After removal, clean the installation points of dust and check the clips for integrity—replace any cracked ones promptly to prevent loosening during reassembly. The entire process requires patience and attention to detail to ensure success on the first attempt.

[AustinFitz]

Removing the Baojun 730 bumper is simple and efficient: Prepare a screwdriver and pry bar, open the hood, loosen about five or six top screws, move to the bottom bolts, release the hidden points in the wheel arches, then gently pry the clips apart with the pry tool. Pay attention to wiring harnesses like fog lights—disconnect the plugs first. Finally, remove the entire bumper. Only basic tools are needed, and the whole process takes about ten minutes. I've practiced this method—it saves time, and the key is to follow the sequence. When reinstalling, align and press firmly, then test the functions to ensure everything works properly.

[OMichael]

My neighbor asked about my experience removing the bumper on the Baojun 730. Last time I helped him with it, I first prepared a screwdriver and plastic pry bar. The removal sequence: first unscrew the 7-8 engine cover screws, then remove the three screws inside the wheel arch, loosen the lower clips, and gently pry it open. Key point – don't forget to disconnect the radar wire connector. During my attempt, one clip broke, so I'd recommend buying spare parts in advance. The entire process took about half an hour. I suggest regularly checking clip aging and replacing them promptly to avoid breakage during removal/installation, which affects efficiency. After finishing, I took the opportunity to clean dust accumulation from the radiator fins – this helps optimize vehicle condition.