···
Log in / Register

How to Make a Left Turn on a Non-Motor Vehicle?

4 Answers
DelTimothy
09/08/25 5:04am
Non-motor vehicles should make a left turn by going around a right angle in two steps and dismounting to push the vehicle within the crosswalk. This is the safest way to cross the street. In this case, non-motor vehicles are treated the same as pedestrians under traffic rules, so they must be dismounted and pushed. Legally, non-motor vehicles are considered as personal luggage. Additionally, from a safety perspective, riding a non-motor vehicle within the crosswalk can endanger pedestrians and affect the judgment of motor vehicle drivers.
Was this review help?
20
2
Share
LeKinsley
09/20/25 3:42am
As a frequent cyclist, I believe the most crucial aspect of making a left turn is safety first. Slow down and proceed cautiously before reaching the intersection, paying close attention to traffic light changes. If the light is red, wait patiently. When it turns green, ensure there are no approaching vehicles from either side before starting your turn. Don't forget to use hand signals to indicate your direction, making your intentions clear to drivers. Maintain balance during the turn to avoid sudden swerves that could cause a fall. Also, be mindful of pedestrians on crosswalks, yielding the right of way when necessary. Exercise extra caution on wet roads during rainy weather, and wear reflective vests to enhance visibility. Developing these good habits and practicing them daily can significantly reduce the risk of accidents.
Was this review help?
20
4
Share
Expand All
IsaacDella
09/20/25 3:44am
For commuting by electric bike, I choose the most time-saving way to make a left turn. At an intersection, I observe the traffic flow. If there aren't many vehicles, I turn left directly during the green light, but make sure there's no danger from either side. In heavy traffic, I use a two-step method: first go straight to the opposite sidewalk and stop to wait, then proceed straight when the lateral light turns green to complete the turn. Always wear a helmet and keep the phone navigation on with sound prompts. Avoid rushing during peak hours—arriving safely is more important. Also, remember to regularly check the brake system to ensure it can stop in critical moments.
Was this review help?
16
2
Share
Expand All
VanClara
11/03/25 4:05am
From the perspective of traffic rules, left turns should strictly adhere to signal indications. When approaching an intersection, slow down and observe the traffic light colors—stopping at red and proceeding at green is fundamental. Before turning, use turn signals to indicate your intention, allowing other road users to understand your plan. Always yield to straight-moving vehicles and pedestrians, never cutting in. At intersections without traffic signals, ensure safety before proceeding. Following these rules ensures the safety of both yourself and others.
Was this review help?
8
3
Share
Expand All
More Forum Discussions

What to Do If the Archive Is Lost Before Taking the Subject 4 Test?

Bring your original ID card, a copy of your ID card, original residence permit and its copy; fill out the "Motor Vehicle License and Certificate Application Form" and pay the service fee. Bring the original organization code certificate of the unit, the original unit authorization letter, the original ID card of the authorized person, the unit's contact number, the authorized person's phone number, and pay the service fee. Visit the vehicle management office website. If you already have an account, log in directly, print and fill out the "Motor Vehicle License and Certificate Application Form", and prepare the original ID card and its copy. If you don't have an account, register as a new user first, fill in the information, wait for the receipt, and you can only apply for a driver's license replacement online after successful registration.
2
1
Share

How to Deal with Sticky Jaguar Buttons?

First, clean with automotive-specific cleaning solution. You can try using alcohol-based substances for cleaning (depending on the dashboard material). If certain solvents (such as perfume or other liquids) have spilled and cannot be cleaned by the above methods, it is necessary to first understand the material of the dashboard and use caution. If cleaning is impossible through various methods (such as when solvents have chemically reacted with the dashboard), the only solution is to have the dashboard professionally refinished. Considering the high cost, if cleaning thoroughly is impossible or the repair cost is too high, it is recommended to replace the part with a new one.
5
2
Share

How to Solve the Squeaking Noise When Engaging Reverse Gear in a Sedan?

If you engage the reverse gear without bringing the car to a complete stop, it can easily lead to gear grinding. Therefore, when shifting into reverse, make sure to firmly press the brake and bring the car to a full stop before engaging the gear. When depressing the clutch to shift gears, ensure the clutch is fully pressed down. Engaging reverse gear while the clutch is still partially engaged can also cause gear grinding. When reversing, avoid excessive speed and refrain from aggressively pressing the accelerator for sudden acceleration, as this can cause significant damage to the straight-cut gears. Additionally, the power transmission of straight-cut gears is very direct and lacks smoothness, so reversing at high speeds can cause considerable discomfort to passengers inside the car.
14
5
Share

What are the precautions for changing tires?

Precautions for changing tires: 1. When replacing, choose tires with the same specifications as the original vehicle assembly; 2. Replace two tires at the same time, and after replacement, each wheel must be rebalanced to ensure the mass distribution of the entire assembly is very uniform; 3. After changing tires, the aging cycles of the new tires and the valve stems differ, and valve stem issues may arise and are not easily detected. It is recommended to replace the valve stems when changing tires; 4. If using the original vehicle tires, follow the manufacturer's installation requirements. For non-original tires, the side with the production date should generally face outward.
14
2
Share

Where are Buick engines produced?

Buick engines are produced in different locations depending on the specific model. The majority of Buick engines for vehicles sold in China are manufactured domestically in China, utilizing German technology, making them domestically produced engines. Some models, however, are imported from Germany. For specific model details, it is recommended to consult local dealers. Buick is a sub-brand of General Motors in the United States. Taking the Buick Excelle as an example, it is an entry-level compact family car under the Buick brand. In terms of body dimensions, it measures 4609mm in length, 1798mm in width, 1486mm in height, with a wheelbase of 2640mm. The Buick Excelle is equipped with tires sized 195/65R15 and 205/55R16.
15
5
Share

How to Step on the Clutch Pedal?

When starting the car, quickly press the clutch pedal down, then rapidly release it to the semi-engaged state, slightly step on the accelerator to increase the engine speed, and then slowly and gently lift the clutch pedal. First, reduce the car's speed until it reaches the point where a downshift is needed, quickly press the clutch pedal, and then follow the principle of 'fast press, slow release, and semi-engagement' to control the clutch. Step on the accelerator to increase the engine speed, then quickly press the clutch pedal, and gently and slowly release it. You can slightly step on the accelerator during the process of gently releasing the clutch. When the car's speed needs to be below 15 KM/H, press the clutch pedal, then use the brake to bring the car to a complete stop. After the car has fully stopped, slowly release the clutch pedal.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.