···
Log in / Register

Can I drive if my license plate is washed away by water?

4 Answers
VonHayden
08/26/25 3:17am
If your license plate is washed away by water, you cannot drive on the road and need to immediately apply for a temporary license plate. You should go to the relevant vehicle management department to reapply for a license plate as soon as possible. Since the replacement cycle for a new license plate takes 8 working days, you must obtain a temporary license plate to drive legally. Below is relevant information about license plates: 1. License plate material: Vehicle license plates are plates hung on the front and rear of the car, usually made of aluminum, plastic, or stickers, displaying the vehicle's registration number, registration area, or other basic information. 2. Function: The license plate is a numbering system for vehicles. Its main purpose is to identify the province, city, or county the vehicle belongs to, and the vehicle management office can use the license plate to find the owner of the vehicle.
Was this review help?
19
1
Share
OMargaret
09/08/25 3:44am
Buddy, if your license plate got washed away by water, you absolutely can't take this lightly and must not drive on the road. Legally, vehicles must have clear and intact license plates to operate. Driving without one is like driving without a license—police will definitely stop you and issue a fine, ranging from a few hundred bucks to points deducted or even vehicle impoundment. I remember a case where someone drove with a missing plate to run errands, got caught, not only fined but also wasted half a day fixing the paperwork. Worse, if an accident happens, the insurance company might deny your claim, arguing you were operating the vehicle improperly, leaving you with even bigger losses. My advice: park the car immediately and head to the local DMV to get a replacement plate. Get a temporary one in the meantime—don’t cut corners and invite bigger trouble.
Was this review help?
1
4
Share
Expand All
BrooklynLynn
10/22/25 3:46am
Listen, I've been through a similar situation before. If your license plate is missing, just don't drive! The law clearly states that license plates serve as vehicle identification. Driving without them carries high legal risks - if traffic police catch you, fines are unavoidable and it may even affect your insurance. A friend of mine once tried driving without plates and ended up with a fine over a thousand yuan plus half a day at the traffic police station, regretting it afterwards. Actually, there are alternative solutions - like asking a friend to drive you to the DMV for replacement plates, or calling a towing service to transport your car directly. These are much better than taking risks. Road safety rules shouldn't be broken - saving a little time might cost you much more money and energy in the long run.
Was this review help?
11
0
Share
Expand All
DiAdam
12/05/25 4:09am
License plate washed off? Stop driving immediately. The license plate is the car's ID card - without it, if an accident occurs, the other party might flee and be hard to trace. Driving without plates is also legally prohibited. I once saw a driver without plates rear-end someone on the highway, and the investigation was a complete mess. Getting replacement plates is quick and easy, just visit the DMV to apply for temporary plates as an emergency solution.
Was this review help?
1
1
Share
Expand All
More Forum Discussions

What to Do When All C1 Driver's License Points Are Deducted?

If all points of a C1 driver's license are deducted, the motor vehicle driver must report to the traffic management department of the public security authority at the place where the driver's license was issued or where the violation occurred within fifteen days to participate in a seven-day study of road traffic safety laws, regulations, and related knowledge. After completing the study, the vehicle management office should conduct an examination on road traffic safety laws, regulations, and related knowledge within twenty days. The C1 driver's license is a type of driving license code, permitting the driver to operate small and micro passenger vehicles, light and micro cargo vehicles, and light, small, and micro special operation vehicles, among others. The examination subjects include four items: traffic regulations and related knowledge, field driving, road driving, and safe and civilized driving common sense.
18
2
Share

Where is the diagnostic port located on the Peugeot 508?

The diagnostic port of the Peugeot 508 is located beneath the vehicle's steering wheel, above the brake pedal. You can identify it by the OBD-labeled latch. Pulling this latch will reveal the internal OBD diagnostic socket. OBD refers to the On-Board Diagnostics system, which continuously monitors the engine's electronic control system and other functional modules of the vehicle during operation. If any abnormal conditions are detected, the system uses specific algorithms to identify the specific fault and stores it as a diagnostic trouble code in the system's memory. The Peugeot 508 is a mid-size sedan with body dimensions of 4870mm in length, 1855mm in width, and 1455mm in height, a wheelbase of 2848mm, and a trunk capacity of 513 liters.
8
1
Share

What to Do When the One-Key Start of Boyue Doesn't Respond?

The solutions for the one-key start of Boyue not responding are: 1. Use another smart key; 2. Place the smart key into the bottom area of the cup holder; 3. Lift the anti-slip mat at the bottom of the cup holder, insert the mechanical key (with the chip side) into the key slot, and then try pressing the start switch. Taking the 2021 Boyue as an example, its body dimensions are 4519mm in length, 1831mm in width, and 1694mm in height, with a wheelbase of 2670mm. This vehicle is equipped with a 1.8T turbocharged engine, delivering a maximum power of 120kW and a maximum torque of 250Nm, paired with a 6-speed manual transmission.
1
3
Share

What is the method for checking car brake pads?

Car brake pad inspection methods are: 1. Listen for sounds - when lightly applying the brakes, if you hear a metallic scraping sound like iron rubbing against iron, it indicates a problem with the brake pads that requires immediate replacement at a repair shop; 2. Check the thickness of the brake pads - new brake pads are about 1.5 cm thick. When visual inspection shows the thickness has reduced to only one-third of the original, increase inspection frequency and be prepared to replace them at a repair shop; 3. Feel the braking force - as brake pads wear thin, braking performance will be affected. Brake pads, also called brake linings, are critical safety components in a car's braking system, playing a decisive role in braking effectiveness. Brake pads typically consist of a steel plate, adhesive heat insulation layer, and friction material. The steel plate is coated to prevent rust, with the coating process monitored by SMT4 oven temperature tracking equipment to ensure quality by detecting temperature distribution during coating.
18
2
Share

What are the causes of brake air pressure failure?

The causes of brake air pressure failure are as follows: 1. The air compressor belt is broken or severely slipping; 2. The air compressor is damaged; 3. Air leakage in the pipeline or joint between the air compressor and the air reservoir or between the air reservoir and the brake regulating valve; 4. The pull arm between the brake pedal and the brake regulating valve is disconnected; 5. The free travel of the brake pedal is too large, preventing the brake regulating valve from opening; 6. The push rod of the brake regulating valve is stuck; 7. Water enters the brake. Relevant information about braking is as follows: 1. Introduction: Refers to the action of stopping or reducing the speed of running locomotives, vehicles, other transportation tools, or machinery. 2. Principle: The general principle of braking is to fix a wheel or disc on the high-speed shaft of the machine, install corresponding brake shoes, belts, or discs on the machine base, and generate braking torque under external force.
13
0
Share

Should You Use Neutral Gear When Waiting at Traffic Lights?

Manual transmission vehicles should be shifted to neutral when stopping at traffic lights. If not shifted to neutral, the engine may stall. Alternatively, you can keep the clutch pedal depressed, but prolonged clutch engagement may cause damage. For automatic transmission vehicles, shifting to N (neutral) gear is unnecessary when stopping at traffic lights. Neutral gear generally refers to the state where the vehicle's gear lever is not engaged in any forward or reverse gear, completely disconnecting the transmission from the drive wheels. In manual transmissions, neutral is the middle position between gears, while in automatic transmissions it's marked with an "N". Automatic transmissions don't require manual gear changes by the driver; the vehicle automatically selects the appropriate gear based on speed and traffic conditions. Typical automatic transmission vehicles have six gear positions arranged from top to bottom: P (Park), R (Reverse), N (Neutral), D (Drive), S (Sport), and L (Low).
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.